cast iron dryer/flaker drum W/end and shaft For drum dryer Diameter: 1,360 mm (53.5 in). Length: 3,500 mm (137.8 in). Heating Type: Steam. Drum Configuration: Single. Pressure: 10.1 bar (147 psi). Temperature: 180.6 °C (357 °F). Heat Transfer Surface Area: 14.9 m² (160 ft²).
double drum dryer with chrome plated rolls .008 to .010 chrome plating on drum surface 75 rockwell hardness drum Serial #17107 2 1/2" rotary steam joint Includes SS fume hood Diameter: 812.8 mm (32 in). Length: 1,829 mm (72 in). Drum Heating-Cooling: Heating. Drum Configuration: Double. Pressure: 11 bar (160 psi). Temperature: 232.2 °C (450 °F). Heat Transfer Surface Area: 4.6 m² (50 ft²).
single drum dryer Drum driven by 12 KW motor and reducer Cored drum Packing gland on shaft Outboard bearings Dual knife discharge, manual knife adjustment into 8" dia screw conveyor Diameter: 762 mm (30 in). Length: 2,591 mm (102 in). Drum Heating-Cooling: Heating. Heating Type: Steam. Drum Configuration: Single. Pressure: 8 bar (116 psi). Temperature: 175.6 °C (348 °F). Heat Transfer Surface Area: 6.3 m² (67.8 ft²).
Equipped with a jacketed bath Sprocket driven hydraulic adjustable discharge knife Diameter: 800 mm (31.5 in). Length: 2,500 mm (98.4 in). Drum Configuration: Single.
single drum dip feed dryer Drum cored for steam heating Manual knife discharge Has 15" x 19" CS jkt feed pan 3/60/230/460 volt, rated 44 rpm max, 8.8 rpm min Diameter: 304.8 mm (12 in). Length: 457.2 mm (18 in). Drum Heating-Cooling: Heating. Heating Type: Steam. Drum Configuration: Single.
cast iron drum for dryer Blt for working pressure of 10 bars Diameter: 995 mm (39.2 in). Length: 3,048 mm (120 in). Drum Configuration: Single. Pressure: 10 bar (145 psi). Temperature: 180 °C (356 °F). Heat Transfer Surface Area: 9.5 m² (102 ft²).
UNUSED cast iron dryer/flaker drum W/end and shaft Diameter: 1,360 mm (53.5 in). Length: 3,500 mm (137.8 in). Heating Type: Steam. Drum Configuration: Single. Pressure: 10.1 bar (147 psi). Temperature: 180.6 °C (357 °F). Heat Transfer Surface Area: 14.9 m² (160 ft²).
cast iron drum for dryer Blt for working pressure of 10 bars Diameter: 995 mm (39.2 in). Length: 3,048 mm (120 in). Pressure: 10 bar (145 psi). Temperature: 180 °C (356 °F). Heat Transfer Surface Area: 9.5 m² (102 ft²).
cast iron dryer/flaker drum W/end and shaft For drum dryer Design pressure 147 psi (10 bar), steam pressure 357 deg F Diameter: 1,360 mm (53.5 in). Length: 3,500 mm (137.8 in). Heating Type: Steam. Drum Configuration: Single. Pressure: 24.6 bar (357 psi). Temperature: 63.9 °C (147 °F). Heat Transfer Surface Area: 14.9 m² (160 ft²).
1.5m OD x 3.5m long cast iron dryer/flaker drum W/end and shaft Design pressure 147 psi (10 bar), steam pressure 357 deg F Diameter: 1,360 mm (53.5 in). Length: 3,500 mm (137.8 in). Pressure: 10.1 bar (147 psi). Temperature: 180.6 °C (357 °F). Heat Transfer Surface Area: 14.9 m² (160 ft²).
drum for dryer Blt for working pressure of 10 bars Diameter: 914.4 mm (36 in). Length: 3,048 mm (120 in). Pressure: 10 bar (145 psi). Temperature: 180 °C (356 °F). Heat Transfer Surface Area: 8.7 m² (94 ft²).
total face cast iron single drum dryer drum manufactured by Black Clawson serial #10062/4130, S.H 51mm, H.D 76mm, H.D.R 2362mm drum cored for steam heating (4) cast iron applicator feed rolls (1) Cast steel knife, gear driven drum motor missing Cooper bearings Diameter: 1,829 mm (72 in). Length: 3,353 mm (132 in). Drum Heating-Cooling: Heating. Heating Type: Steam. Drum Configuration: Single. Pressure: 6.9 bar (100 psi). Heat Transfer Surface Area: 16.7 m² (180 ft²).
Double Drum Dryer with vacuum housing and vacuum skid Chrome plated carbon steel drums with 304 stainless steel, jacketed vacuum housing Sanitary and polished construction suitable for food and pharmaceuticals but can be used for any batch processes, or converted to a continuous process. Drum rolls have a 16 micro-inch finish, all internals have a 32 micro-inch finish External finish is 2B or bead blast Vacuum housing is rated to operate at full vacuum Drums are rated for 160psi/FV @ 375 degrees F (NB# 9918 and NB# 9919) Designed for use in class 1 division 2 atmospheres 1287 lbs./hr. of H2O and Ethanol utilizing a 3.8 to 4.6 lbs./hr./ft2 evaporation rate Spring loaded screw type manual adjustment assemblies with digital drum gap display Pneumatic cylinder adjustable 304 stainless steel knife bars with clamp and acme thumb fasteners and pneumatically operated stainless steel end scrapers 8 zone steam jackets rated for 160 psi at 375 degrees F (4) 6” tri-clamp top chamber inlets, (4) 4” tri-clamp product feed inlets, (2) 14” 150lb ANSI flange vapor outlets (14) 1/2” NPT hot water jacket nozzles, (2) 1.5” NPT hot water jacket nozzles, (6) 4” tri-clamp internal drains, (10) 4” tri-clamp light ports The Vacuum system is rated for 140 CFM, and is 304 SS contact, capable of handling 1,340 lbs./Hr. of vapor rate Manufactured by Wintek Corp Model # C380R50-WSS-=140/2-1FRss, serial # 140321 The skid mount system contains the following equipment: One-(1) 380 square foot, 304 SS contact, shell and tube pre condenser TEMA C AEL, requires 180 GPM of cooling water at 50 degrees F One-(1) Non code 304 SS 50-gallon receiver, with condensate pump One-(1) Vacuum pump, SS wetted side, manufactured by Dekker, rated for 140 CFM, direct driven by a WEG 10 HP motor at 1750 rpm One -(1) separator tank, non-code 304 SS, approximately 10 gallons One- (1) Sealant heat exchanger, non-code, plate and frame, SS process side, requires 10 GPM cooling water at 50 degrees F All equipment mounted in a CS frame work with ss interconnecting piping The control system is a free standing Panel View Plus 1000 in a nitrogen purged enclosure good for Class 1,Division 2, Group D It is located local to the machine, but will also send a signal to a remote control room Located outside the classified area are the motor VFD, and electrical controls Diameter: 1,524 mm (60 in). Length: 3,048 mm (120 in). Drum Heating-Cooling: Heating. Heating Type: Steam. Drum Configuration: Double. Pressure: 11 bar (160 psi). Temperature: 190.6 °C (375 °F). Heat Transfer Surface Area: 29.2 m² (314 ft²). Vacuum Rated: Yes. Vacuum Housing: Yes. Vacuum Housing MOC: Stainless Steel 304L.
single drum dip feed dryer M/C #4586 Drum cored for steam heating (2-50mm openings) Speed 1 to 6 rpm Drum totally enclosed in 316 stainless steel chamber Motor: non-flameproof motor Drum with monel adjustable stainless steel knife/scrapper Dip tray 1522mm long x 736mm wide Openings: 2-50mm, 1-25mm; hood with 1-300mm, 2-100mm. All wetted parts 316 stainless steel. (3) 400mm long x 300mm wide inspection covers. Diameter: 456 mm (18 in). Length: 1,370 mm (53.9 in). Drum Heating-Cooling: Heating. Heating Type: Steam. Drum Configuration: Single. Pressure: 7 bar (101.5 psi). Temperature: 174 °C (345.2 °F). Heat Transfer Surface Area: 1.95 m² (21 ft²).
cast iron R Simon single drum dryer Dryer includes (3) + (1) 316SS 9" feed rolls working pressure 3 bar (6 bar tested) w/(2) pneumatic and (1) manual operated feed roll scrapers Scraper knifes mfd form tufnol bear brand material Pneumatically operated (non-oscillating) cast iron knife bar Knife mfd in cast steel Motor: 28 amps variable speed gearbox Radicon reduction gearbox SS paddle conveyor w/inspection panels powered by 1.5 KW geared motor Unit can be supplied w/pneumatically operated traversing gear if required Control panel consisting of all pneumatic controls and electrical timers for feed roll scrapers Was rebuilt Diameter: 914.4 mm (36 in). Length: 2,540 mm (100 in). Drum Configuration: Single. Pressure: 7 bar (101.5 psi). Heat Transfer Surface Area: 7.4 m² (80 ft²). Number of Applicator Rolls: 4. Applicator Roll Diameter: 228.6 mm (9 in).
chrome plated drum dryer Single drum dryer varispeed motor (4) applicator rolls, manually adjustable Drum gear driven (no motor). Openings: drum 1-87mm, 1-19mm Diameter: 1,500 mm (59.1 in). Length: 1,700 mm (66.9 in). Drum Heating-Cooling: Both. Drum Configuration: Single. Number of Applicator Rolls: 4.
chrome plated single drum dryer Has jkt feed pan Belt driven by US varidrive Motor: 3 phase 3/60/230/460 volt, 5.4 rpm min 54 rpm max Has hood 12" x 30" side access panel Has 8" x 8" discharge w/chute and manual slide design gate valve Diameter: 508 mm (20 in). Length: 508 mm (20 in). Drum Configuration: Single. Heat Transfer Surface Area: 0.84 m² (9 ft²).