Type: Dryer-Spray
Manufacturer: Niro
Model: F10-1-D-P-S-N
Condition: Used
Material: Stainless Steel 316
Diameter: 2,134 mm (84 in)
Atomizer Type: Rotary Disc-Wheel
316SS (polished) Chamber dimension 7' dia x 45" str side w/7' cone btm Requires a Niro wheel atomizer belt drive by 3 HP, 3/60/230/460 volt, 3450 rpm TEFC motor 20" side access door W/steam coil mfd by Schenaball, 37.5 sq meter, 7 bar, SN 19605 W/blower and cyclone
Type: Dryer-Spray
Manufacturer: Anhydro
Model: III-A size #2
Condition: Used
Material: Stainless Steel 304
Diameter: 2,394 mm (94.3 in)
Atomizer Type: Rotary Disc-Wheel
Flat bottom, with a center bottom discharge Chamber diameter 94.25". Inlet air to the chamber is heated by a direct gas fired air heater Gas Air heater is manufactured by Maxon, type Air Flow Burner series NP. The burner uses a spark ignited pilot and control is by Maxon Series "Q" butterfly valve. Hot air enters the chamber through an air distributor on top of the chamber. The distributor has vanes that are adjustable to control the air flow pattern into the chamber. As a standard feature, a cooling ring is built in around the inlet area. This prevents particles from becoming overheated in the event they contact this area. This prevents particles from becoming overheated in the event they contact this area. If the cooling chamber is needed, it will use 375 CFM at 2" W.C. Exhaust blower is manufactured by New York Blower, and is a type "P" pressure blower. It is rated for 750 cfm, and is belt driven by a 5 HP motor at 3600 rpm. Electrical spec for the blower motor is 3/60/230-460V and the motor style is TEFC. It sits on a 184 T frame. Dryer Dimensions from Drawing L-2808-0101: Chamber diameter 7' 10.25", Height 11' 9". 4' 2" from Grade to bottom of dryer. Footprint: Approximately: 14' x 11'. Gas pressure needed, 3 psi, Power needed for Controls 115 VAC 1 ph, 60 Hz, Power required for motors 240 VAC 3 Ph, 60 Hz.
Evaporation Rate: 40.8 kg/h (90 lb/h). Inlet Temperature: 204.4 °C (400 °F). Outlet Temperature: 93.3 °C (200 °F). Heating Type: Gas. Height: 2,134 mm (84 in).
Type: Dryer-Spray
Manufacturer: APV Anhydro
Condition: Used
Material: Stainless Steel 316
Diameter: 1,245 mm (49 in)
Atomizer Type: Rotary Disc-Wheel
sanitary Two types of atomizers: (1x) Belt driven centrifugal atomizing disk & (1x) Down spraying, two fluid, external mixing, air atomizing nozzle APV Anhydro Compact Spray Dryer Air Inlet temperature 200 -300 degrees C (390-670 degrees F), Exhaust air temperature 90 degrees C (195 degrees F) Food grade construction Heat for hot air is natural gas fired by an Eclipse burner rated for 240,000 BTU This system has two forms of atomization, #1)Belt driven centrifugal atomizing disk, driven by a 1 HP motor. #2) Down spraying, two fluid, external mixing, air atomizing nozzle type. Dry product is separated in a SS cyclone, 12" top diameter x 48" high with a 4" cone bottom . Dust is collected in a CS bag house, 36" wide x 86" long x 14' high. 16 Bags with 4" diameter x 48" long socks, approximately 64 Sq. Ft. of filtration area TEFC Hi efficiency. Feed pump is driven by a 0.5 HP motor. Straight wall internal is 60".
Evaporation Rate: 31.8 kg/h (70 lb/h). Inlet Temperature: 354.4 °C (670 °F). Heating Type: Gas. Counter Current or Co Current: Co Current. Explosion-Shock Resistant: Yes.
Type: Dryer-Spray
Manufacturer: Tetre
Model: Type 150
Condition: Used
Material: Stainless Steel 304
Diameter: 2,500 mm (98.4 in)
Atomizer Type: Single Fluid Pressure Nozzle
System consists of: (1) Tetre 304 stainless steel spray dryer, spray nozzle feed, evaporation 100-160 kg/hr@ 160-195 deg C, 2.5m diameter x 8.5m straight side x 3m high cone section, 2 x hinged inspection doors, mounted on carbon steel mounting ring, (1) Maxon gas fired burner, serial # 600200332-03, 50 HZ, 110 volt, heat value 10 kwh/nm3, inlet pressure 100 mbar @ 150 degrees c, min heat input (HHV) 18 kw, max heat input (HHV) 600 kw, duct pressure -1 bar, (1) stainless steel cyclones, (1) rotary valve (1) 2.22 m3/sec exhaust fan, manufactured by Pollrich, type S38031RWIII, 2720 -2800 rpm max, 280 degrees C (max) (1) kinpactor, manufactured by AAF International ltd, (1) stainless steel vane demister , manufactured by AAF International ltd, type Vane-pak, size DF-100, serial # AP03980, (1) 500mm diameter stainless steel single deck vibratory compact sieve, model 17240, manufactured by Russell Finex, serial # DF1854, 500mm diameter x 60mm deep deck with top cover, vibratory motor type MVS1-3/500-890, rated 0.45 kw, 3/50/220-240/380-415 volt, 3000 rpm (1) 2.1 cubic feet (0.06 cubic meter, 60 liter) stainless steel ribbon blender. manufactured by Hosokawa, type HMC-60, serial # 648010100, rated 3 kw, ribbon speed 158 rpm (max), interrupted ribbon design, trough 1.2m long x 300mm wide x 350mm deep, driven by 3 kw, 3/50/380/415 volt, motor via gearbox, hinged top cover, (1) control Panel
Evaporation Rate: 160 kg/h (352.7 lb/h). Inlet Temperature: 195 °C (383 °F). Air Flow Rate: 7,990 m3/h (4,703 CFM). Heating Type: Gas. Explosion-Shock Resistant: Yes. Height: 12,500 mm (492.1 in).
Spray dryers convert liquids into dry powders by atomizing the feed into a hot air stream, allowing for fast, controlled evaporation. Ideal for heat-sensitive products, spray dryers are used in a wide range of industries to ensure consistent particle size, solubility and purity. With over 47 years of experience, IPP supplies surplus, secondhand and used spray dryers from 20 complete process plant sites and an unmatched inventory of more than 15,000 ready-to-ship systems.
Spray dryers can be configured for co-current, counter-current or mixed-flow operation and often feature cyclones, bag filters or scrubbers for product recovery and emission control.
Spray dryers are built for cleanability, thermal resistance and corrosion protection:
Learn more about spray drying technology and applications from Chemical Engineering.
Search the IMS inventory or contact IPP’s team of experts to find a used, secondhand or surplus spray dryer that meets your specifications. From lab-scale systems to industrial towers, IPP helps you save time and money with ready-to-ship solutions.