Quote
Request Quote

Extruders from IPP. Over 31 pieces for sale. Chemical Equipment and Process Equipment buy unused, surplus, second hand or used here.

Featured Extruders

69.9 mm (2.8 in) Stainless Steel 316 Extruder

Stainless Steel 316 Extruder

Type: Extruder

Manufacturer: Reifenhausser Kg

Model: RH381-1-70

Condition: Used

Material: Stainless Steel 316

Diameter: 69.9 mm (2.8 in)

Feeder: Yes

single screw extruder line General purpose screw and feed hopper. Production rate: 75 Kg/hr maximum polypropylene. Barrel has (8) heaters with (3) electric fans Extruder driven by a 60 HP (46 KW) DC motor. Line is complete with a15' long x 12" wide x 8" deep stainless steel cooling bath with air knife and (1) automatic 100mm granulator, Type ASG-10, serial #00-015-2204. Driven by 2.2 KW motor. Extruder is complete with control panels.

Heating type: Electric. L/D Ratio: 30:1.

65 mm (2.6 in) Carbon Steel Extruder

Carbon Steel Extruder

Type: Extruder

Manufacturer: APV

Model: MP 2065 Kneader

Condition: Used

Material: Carbon Steel

Diameter: 65 mm (2.6 in)

Number of Heating Zones: 5

twin screw Ko-Kneader system, (1) Baker Perkins 800mm diameter chilled drum roll cooler, series 2000, serial #65712, drum with pre-breaker and Kibbler granulator, granulator driven by 10HP, 1500 rpm motor, pre-breaker driven by 1HP, 150 rpm motor, chill roll motor driven by 5 HP, 25 rpm motor, (2) 350 liter high intensive mixers, driven by 37kw, 3/50/415 volt, 1475 rpm motor, (1) chiller, (1) buffer hopper with bag filler

Screw Length: 1,600 mm (63 in). Feeder: Yes. Heating type: Electric.

70 mm (2.8 in) Carbon Steel Extruder

Carbon Steel Extruder

Type: Extruder

Manufacturer: Buss

Model: TCS-70-16D Kneader

Condition: Used

Material: Carbon Steel

Diameter: 70 mm (2.8 in)

Number of Heating Zones: 5

single screw Ko-Kneader system, proceesing length 16 L/D, carbon steel heated screw, screw oscillation stroke 10.5mm, screw root diameter 45mm, Theoretical pitch in kneading zone (2-spirals) 42mm, pitch in infeed zone (1-spiral) 38mm, free zone (5-barrel section) 2.04 dm3, screw driven by a 2-speed motor, 45kw, 3/50/380/400/415/660/690 volt, 1480/1475 rpm or 55kw, 3/60/440 volt, 1775 rpm, cast chrome steel barrel, barrel with special high nickel content carbon steel liner and kneading pins, barrels steam/water heated, (4) Regloplas type P160/9/SG5/IK/R145 water/steam heater temperature controllers, 6.5 ltr volume, rated 6 bar @ 160 deg C, (1) 600mm wide x 3m long chilled rubber belt conveyor with Netzsch Condux Granulator, (2) Tricool chillers, 2) 21.6 cubic foot (0.6 cubic meter) carbon steel ribbon mixer, 550mm wide x 1680mm long x 700mm deep, interupted ribbon, driven by 7.5 hp, 3/60/415 volt, 1405 rpm motor, end bottom discharge with pneumatic operated slide valve, 2-650mm x 650mm inspection ports with hinged covers,

Screw Length: 1,300 mm (51.2 in). Feeder: Yes. Number of Cooling Zones: 1.

242 mm (9.5 in) Aluminum Extruder

Aluminum Extruder

Type: Extruder

Manufacturer: Henry Simon

Condition: Used

Material: Aluminum

Diameter: 242 mm (9.5 in)

Temperature: 90 °C (194 °F)

single screw plodder/extruder.

Production rate: 500 Kg/hr maximum (soap)

Worm speed ? rpm

Cast iron barrel and removable nose cone,

both with aluminum lining, aluminum worm screw. Barrel with cooling/heating jacket, nose cone with electric heater.

Unit with feed hopper. Hopper with roll feeder,

1.1 KW, 3/50/220/380 volt, 1390-42 rpm geared motor

(1) carbon steel screw. Control panel. Unit base mounted.

Feeder: Yes. Heating type: Electric.