New and Used Equipment

• Side discharge with automatic valve Agitator Cored for Heating/Cooling: Yes. Vessel Liquid Capacity: 400 gallons.

Size 16Trough dimensions 31" x 49" x 47" deep, hinged cover w/counter balance, w/cored dispersion type mixing blades. Packing gland on shafts Shafts geared both ends and driven by Pacemaker 200/100 HP, 3/60/460 volt, 1770/885 rpm motor, Frame #449T, w/gear reducer. Output rpm on front blade 42/21, rear blade 25/125driven by 5 HP motor.

• New Base Reactor Body (with covers) Bare reactor price in sales comments.
• Can be upgraded w/ drive system to reactor
• Both ASME National Board # and CE Marked
• Interchangeable with UGE Agitation Systems & Pfaudler Agitation Systems

• Sheathing covering Insulation rock wool and puff , 304 SS sheathing completely sealed to 0.4 bar
• With thermowell and dip pipe.
• Internal : Buff polished to 240 Grit.
• External: Buff polished to 180 Grit.
• UNDER FABRICATION, WILL BE FACTORY COMPLETE WEEK OF DEC 15 2025! Support Type: Lugs.

• REBUILT 2.1 cu. ft. operating capacity Jacketed Porcupine Processor designed for batch operation manufactured by Bethlehem Foundry and Machine Company
• Shell is rated for MAWP 50 PSI
• Porcupine surface area is 15 sq. ft. jacket is 9.4 sq. ft. Head flats are 3/4" and 3 & 7/8"shell is 1/4" and jacket is 5/16"
• 230/460 volt motor with a Reynolds reduction gear
• with a 207:1 ratio Steam or hot oil inlets and outlets are all 1" NPT Process inlets an are two 3" and outlets are 3.5"
• Rebuilding included the following: Unit is stripped, cleaned, and shaft and jacket pressure tested Gearbox drained, cleaned, checked and refilled. Motor replaced, unit test run. Stuffing box gaskets replaced and new rotary joint installed. New top head cover gasket replaced, Test run and painted, new coupling guard installed.
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Total Heat Transfer Surface Area: 24.4 ft². Porcupine Agitator Pressure: 150 psi. Porcupine Agitator Temperature: 600 °F. Size: 1203.

UNUSED

Internal finish 240 grit buff polished-Bright polished, external buff polish to a matte finish. ASME NB rated, and "U" stamped.

welded dish heads (2:1) 12 mm thick

Coil: 114 mm OD x 4 mm thick,

Limpet covers bottom dish and 2615 mm of straight side (pitch 150mm). Coil heating surface area.

With Insulation rings and upper drip ring. Two top lifting lugs and one tailing lug.

20" Manhole with Cover and davit arm assist, one 6" sight glass, Support Type: Lugs.

MFR # 12269 Model SA-3000 Special three top lifting lugs, six leg couplings, four side wall lugs Shell=1 & 1/64", heads=1 & 1/64", jacket =5/8" PTE size 10 drive with an EX proof 20 HP motor and a dry seal. 36" main cover. 18" man way with pro ring and sight glass assembly with man way assist.

• Alloy C276 Vacuum Conical Screw Dryer.
• Coil jacket, Shell rated 88FV.
• 103" diameter x 117" length.
• Welded dished top head.
• Orbital acting screw agitation. Johnson Joint attached to top.

jacketed double arm mixer Shell rated atmospheric Front mixing blade 45/30 rpm, rear mixing blade 30/20 rpm x-proof motor and starter box.

Niro (Bowen Design) Spray Dryer With BB-3 Type Spray machine Conical Bottom drying chamber is 12' diameter x 6' 7" straight side, and utilize a co current air flow design. Elevation to top of dryer is 25' 7". This is a complete system with the spray dryer and bag house mounted out doors. Feed related equipment is mounted indoors on a skid. Dryer details are as follows: Supply air; 1385 acfm. Natural gas; 27.9 acfm. Feed; 1725 lbs/hr. Product 525 lbs/hr. Evaporation rate 1200 lbs./hr. Process gas inlet temp. = 1100 degrees F. BB-3 spray machine with complete controls including a Penthouse control panel, feed valve, automatic force oil lube system by Sloan Brothers, and Magnetek GPD 505 VSC variable motor speed system. Bag house is manufactured from 321 SS, rated for 400 degrees F, with an air volume of 1850 scfm, and air to cloth ratio of 3.9:1. Blower is CS, by New York blower, series 45, size 224 and rated for 3000 cfm at 3127 rpm. Other support equipment includes a 400 gallon, fiberglass mixing feed tank, and related pumps. Auto valves are by Fischer, instrumentation is by Rosemount.

fermenter Tankki OY agitator drive, serial # 8420, driven by Sew-Eurodrive, type FAF80-DV160-M4, 11kw, 3/50/400/690 volt, 1440-105 rpm geared motor, (3) 6-blade turbine type agitators, dry running mechanical seal,

• Jacket Coverage bottom dish and 7/8 of shell height.
• Motor "Foot Mounted TEFC, UL, EX Proof, 60Hz, 230/460V"
• Sheathing covering Insulation rock wool and puff , 304 SS sheathing completely sealed to 0.4 bar
• With Thermowell and dip pipe
• Internal finish: buff polish 240 grit
• External finish Buff polish 180 grit Support Type: Lugs.

Shell rated 150/FV @ 450 degrees F. Conventional jacket 150/FV @ 450 degrees F with welded 2:1 elliptical heads Alloy mixer with dual tier agitation, lower is a CBT, upper is a PBT

• mobile laboratory filter/dryer with tilting mechanism,
• design pressure internal 1 bar + full vacuum @ -20/150 degrees C, jacket: 6 bar + full vacuum @ -20/150 degrees C,
• all wetted parts are Hastelloy C22,
• 50 liter slurry capacity,
• 20 liter cake capacity,
• 350mm diameter x 680mm straight side,
• 6-30rpm shaft speed,
• agitator driven by 1.5kW, 3/50/230/400 volt, 1420 rpm CE ATEX EExd IIB T4 IP55 motor,
• hydraulic driven agitator raise/lower mechanism with powerpack,
• alloy 22 bellows on shaft,
• flat bottom filter plate with mesh filter and can be rotated for cleaning,
• manual vessel tilt mechanism,
• strip sight glass on side for measuring cake depth,
• approximately 100mm side discharge which is fully contained in a glovebox.
• all mounted on stainless steel frame with wheels for full mobility,
• design code ASME VIII DIV 1 (1998) + A '00'
• Can be used with 248331 APOVAC system for vacuum at an additional cost.

• design pressure 1.030/3.5 bar @ -15/100 degrees C,
• design code ASME VIII DIV. 1. 1989 (DEC 90 ADDENDA)

With (2) PTFE lined centrifugal pumps, manufactured by Richter Chemie, type PCK/F 32-160, 2900 rpm, 165mm diameter impellor, mounted on a base plate,

100 kg typical batch weight (Polished to a 0.1 Ra Min finish) Standard capacity range is 120-240 liters. This granulator features a through the wall design where the utilities are located outside the clean room. It has a jacket for the base and bowl with temperature sensor. The main impeller is capable of being raised and lowered. The side chopping system has a variable speed control. Discharge is into a through the wall mill model U-20. Features sanitary design and Clean in place. This multipurpose machine can process dry powders, aqueous and solvent granulations, effervescent products, and melt palletization applications. This machinery is electronically controlled. Can be used with Fluid bed dryer IPP stock # 233968.

• Trailer mounted set. Oil Type Required API CF-4
• Complete Service at 11207, Hours includes New Batteries, Oil & Filters, Air Filters, Fuel Filters.

• design pressure internal 4 bar + full vacuum @ -29/185 degrees C,
• jacket 10 bar + full vacuum @ -29/185 degrees C,
• shaft 10 bar + full vacuum @ -29/185 degrees C,
• shaft driven by 22/15kW, 3/50/415 volt, 1465/980 rpm IP55 motor via a 24.20:1 ratio gearbox,
• half pipe coil jacket on body and ends
• center bottom discharge,

dryer with

(1) (1) 150 liter 316L stainless steel pressure tank (jacket expansion tank), pressure -1/6 barg @ 185 degrees C,

(1) 316 stainless steel centrifugal pump, manufactured by Girdlestone, type 12CS3G, serial #53534, size 80-50-175, driven by 11kW, 3/50/415 volt, 2940 rpm EEx de IIB T4 motor, mounted on a baseplate, Dust Collection: Yes. Jacket Material: Stainless Steel 316L. Jacket Pressure: 10 bar. Jacket Temperature: 185 °C. Jacket Type: Half Pipe/Limpet.

• 10000 liter working volume
• max working pressure internal -1/6 bar @ -25/160 degrees C (11610 liter),
• jacket -1/10 bar @ -25/150 degrees C (721 liter),
• EX II 2 G classification,
• CE0034,
• glass type 3009-U
• white glass body, baffles and blue glass shaft
• design code AD-M 2000,

• reactor/crystalliser,
• design pressure internal 6 bar + full vacuum @ -29/185 degrees C (12300 liter), jacket 10 bar + full vacuum @ -20/185 degrees C,
• driven by 15kW, 3/50-60/690-400/660-380/415-440 volt, 1467/1463/1471/1763 rpm ATEX EExde IIC T4 IP65 motor,
• 3-sets of 2-blade Viscoprop pitched paddles, 1-set of 2-blade Endorgan pitched paddle on the bottom of the shaft,
• gas type Burgmann double dry running mechanical seal,
• design code: PD5500 - 2006 - module G - gas group 1, CAT 2, CE 0878,

• Body Only, base body
• Four Bosses for agitator.
• Glass type PureGlass (Pharma Grade)
• Exterior Paint :UGE blue Acrylic Polyurethane
• legs with flat plate feet, with 18” clearance bottom nozzle to floor.

• design pressure internal -1/6 bar @ -29/200 degrees C,
• jacket -1/10 bar @ -29/200 degrees C,
• CE0038,
• glass type 9129,
• driven by 45-52kW, 3/50-60/690-400/660-380/415-440 volt, 1477/1473/1479/1773 rpm EExd IIB II 2G T4 ATEX motor via a reduction gearbox,
• 90 rpm shaft speed,
• white glass body, blue glass shaft and baffle
• design code: ASME VIII DIV 1, 2004 ANNEXE Z and essential safety requirements of PED/97/23/EC,

15-25kg Paglierani valve bag weigh, bagging and filling line, system consists of: (1) Paglierani weighing, bagging/filling machine with bag shaker as it is filling which Driven by 1.1/1,27kw, 3/50/60/230-400/265-460 volt, 910/1090 rpm ATEX Ex e 11 T4 motor, powder is screw feed into the bag, screw driven by 2.2/2.5 kw, 3/50/60/230-400/265-460 volt, 1420-1690 rpm ATEX Ex e 11 T4 motor bag support mechanism driven by 1.1/1.27 kw, 3/50/50/230-400/265-460 rpm ATEX Ex e 11 T 4 motor, (1) 304 stainless steel feed hopper with screw discharge and 25 liter stainless steel cyclone vacuum powder conveyor, cyclone type VF02, manufactured by Palamatic, serial #B120 203 C_02, -10/40 degrees C, 1-2.5 m3/hr, (1) manually fed bag conveyor (1) bag erector and feeding machine (1) control panel

C 3-stage reciprocating Boil-off-gas (BOG) compressor system maximum allowed rod. Load 100kN, rated discharge pressure of final stage 69 barg, suction pressure 1st stage 0.05 bar @ 30 degrees C, 2nd stage 4.6 bar @ 45 degrees C, 3rd stage 27.7 bar @ 45 degrees C, discharge pressure 1st stage 4.7 bar @ 176 degrees C, 2nd stage 27.9 bar @ 190 degrees C, 3rd stage 69 bar @ 160 degrees C, driven by a 250kw, 3/50/400 volt, 594 rpm ATEX 1022 EExd II B T4Loher motor, (1) 550 liter stainless steel vertical pulsation dampner vessel, manufactured by Nadoba Stabilini, serial #954, pressure 0.05 bar @ -118/+30 degrees C, 610mm diameter x 1740mm straight side, weld dished top and bottom, (1) 125 liter carbon steel horizontal pulsation dampner, manufactured by Tlakova Nadoba Stabilini, serial #955, pressure 10.7/69.6 bar @ 57/159 degrees C, weld dished ends, (1) carbon steel tube and shell horizontal 1st stage intercooler, manufactured by APL Apparatebau AG, serial #W8227/EC22601, tubeside pressure 10 barg @ -10/200 degrees C (27 liter), shell 10 barg @ -10/200 degrees C (53 liter), (1) carbon steel tube and shell horizontal 2nd stage intercooler, manufactured by APL Apparatebau AG, serial #W8228/EC22602, tubeside pressure 29 barg @ -10/200 degrees C (20 liter), shell 10 barg @ -10/200 degrees C (55 liter), (1) carbon steel tube and shell horizontal 3rd stage intercooler, manufactured by APL Apparatebau AG, serial #W8229/EC22603, tubeside pressure 78 barg @ -10/200 degrees C (9 liter), shell 10 barg @ -10/200 degrees C (42 liter), system also includes interconnecting pipework, valves, etc, ALL CE MARKED