Quote Cart
Type: Still
Manufacturer: Steris Finn-Aqua
Model: 3000-G
Condition: Used
Material: Stainless Steel 316
Controls: Yes
Support Type: Skid
4700 lbs/hr
Pure Steam Generator
Falling film design to remove pyrogenic material
Steam heated.
Electricals rated 3.0 kW, 480 volt, 60 cyc, 5.2 amp with 0.5 kW 120 volt 4.2 amp, 60 cyc controls.
All product surfaces are sanitary 316SS construction. Skid
with process controls in a SS control cabinet
Sesigned to consistenly generat Pure Steam for usin in Pharma and biotec industries.
Orientation: Vertical.
Type: Still
Manufacturer: Steris Finn-Aqua
Model: 1500-H-5
Condition: Used
Material: Stainless Steel Austenitic
Diameter: 300 mm (11.8 in)
Length: 2.7 m (8.7 ft)
multi-effect WFI stills system the Finn Aqua Multiple Effect Water Stills uses an enhanced falling film evaporation technology that removes impurities at high velocities, delivering the highest quality water for injection. the Multiple Effect Water Still uses a staged evaporation and condensation process to produce water for injection. Plant steam is applied only to the first column evaporator (effect) with the subsequent columns using the steam produced in the previous column as the source of energy. Similarly, cooling water is applied only at the condenser to condense pure steam into water for injection. The columns subsequent to the first column use feed water as the cooling source, which is evaporated, as the pure steam from the preceding column is condensed producing water for injection. Produced distillate and remaining pure steam is condensed in the condenser and flowing further to the plant’s water for injection tank. system consists of (5) ) 316L stainless steel (1.4404/1.4571) vertical heat exchangers, pressure 8 bar @ 175 deg C (9.7ltr), (1) 200ltr 316L stainless steel (1.4404/1.4571) tube, head and shell horizontal condenser, pressure 2 bar @ 133 deg C, driven by a 3 kW 2900 rpm motor, (5) stainless steel Pall Filters, (1) 2500 liter 316L stainless steel (1.4571 ) vertical pressure tank with half pipe coil, pressure -1/6 bar @ 200 deg C, 1.8m diameter x 1.5m straight side,
Pressure: 8 bar (116 psi). Temperature: 175 °C (347 °F). Column: Yes. Multi Effect: Yes.
Type: Still
Manufacturer: Distillation Engineering Co.
Condition: Used
Material: Stainless Steel 316
Diameter: 304.8 mm (12 in)
Length: 2 m (6.7 ft)
with out a still pot. Needs a 750-1000 gallon reactor to complete (sold separate) Designed to bolt onto the top of a reactor with a 750-1000 gallon capacity. (depending on the chemical service) The system consists of the following parts First a 12" x 80" SS packed column, second a top mounted re-boiler, and third a reflux tank. The column section is 12" diameter x 80" overall length. 316 SS, NB # 205, rated for FV/125 psi at 500 degrees F. Manufactured by Roben. With a packing support 10" from the bottom of the column. Estimated packed capacity is 5 ft.3. The U-Tube condenser is top mounted to the column. It is 150 ft.2, The shell is 316 SS. NB # 4892. The shell is rated for FV/150 psi at 450 degrees F The tubes are rated for 100 psi at 450 degrees F. It is manufactured by Roben, serial # 81034. It is 18" diameter x 107" overall length. Two pass tube side. With 2" tube nozzles. The reflux/receiver tank has a 60 Gallon capacity and is manufactured from 316 SS material. It is orientated vertically. The dimensions of the vessel are 24" diameter x30" straight side,
Still Type: Column Still. Pressure: 8.6 bar (125 psi). Temperature: 260 °C (500 °F). Column: Yes. Orientation: Vertical.
Type: Still
Manufacturer: Paul Mueller
Model: P7140
Condition: Used
Material: Stainless Steel 316
Diameter: 1,219 mm (48 in)
Length: 2.7 m (8.9 ft)
1,200 lbs./hr PyroPure Clean steam generator Produces pyrogen free pure steam that meets USP requirements With external shell and tube evaporator, double tube sheet 316LSS contact surfaces, polished to 20 ra max. blowdown cooler which serves as a pre-heater for water entering the evaporator steam seperator and feedwater pump Evaporater NB # 32477 serial #4767410-1 Shell rated for 150/FV psi at 366 degrees F tubes rated for 150/FV psi at 366 degrees F Cooler NB #32664 Serial # 4864670-1 shell rated for FV/150 psi at 336 degrees F tubes rated for FV/150 psi at 336 degrees F Feed water pump, 316SS manufactured by Fristam Pump direct driven by a 3 hp 3500 rpm AC motor All parts mounted on a skid with the following controls AB PLC control with Panel View Plus operator interface I/O cabinet and Motor staring cabinet complete with breaker Feedwater inlet is 1" TC sanitary Steam inlet is 1.5" flange(150 psi max) Pure steam outlet is 2" TC sanitary Condensate outlet is 1" FNPT drain is 1" TC, and instrument air is 1/4" FNPT Dimensions are 48" wide x 46.5" deep x 107" high. Shipping weight is 2,150 lbs.
Pressure: 10.3 bar (150 psi). Temperature: 168.9 °C (336 °F). Controls: Yes. Support Type: Skid. Orientation: Vertical.