New and Used Equipment

Manufactured by Estrella AG in Ettingen, Germany Packed column consisting of (3) Clamped mid sections, each 2.000 mm long x 788 mm inside diameter, openings each section: (1) NW 150, (1) NW 50; (1) clamped dished top, 1.120 mm long x 788 mm inside diameter

• Plates are FDA approved and non gasketed.
• Polypropylene plates and frames and all Stainless Steel skeleton.
• Approximately 38 chambers.
• 4 eye closed delivery, 1" inlet and outlets.
• Manual closure with Hydraulic Assist manufactured by SPX. Plate Diameter or Width: 800 mm. Plate Height: 800 mm. Plates Shifted By: Manual.

• Plates are FDA approved- Non Gasketed.
• Polypropylene plates and frames and all Stainless Steel skeleton.
• 44 chambers.4 eye closed delivery,1" inlet and outlet.
• Manual closure with Hydraulic Assist manufactured by SPX. Plate Diameter or Width: 800 mm. Plate Height: 800 mm. Plates Shifted By: Manual.

Trough rated 80 psi @ 650 F. Double Screw design with 3" Johnson joints on shafts. Trough rated 80 psi @ 650 F. Double Screw design with 3" Johnson joints on shafts. Total heat transfer area is 571 Sq.Ft., screws are 445 Square foot surface area, jacket is 126 Sq.ft. surface area. Heat transfer medium is water. Heat transfer area for screws is rated for 264 gallon fluid volume, 158 gpm flow rate. Contact parts are carbon steel, flight thickness 5/16". Net Trough volume is 74 Cubic foot, rated 60" wc in the trough. Jacket rated for 92 gallons, 39 gpm flow, CS construction. Flat cover on trough. with a DC Drive controller. 20.7 minutes residence time. Originally used as a cooler. Feed rated 15,000 lbs/hr; Bulk density 70; Material Flow 2/4 CFH; Temperature 1560 degrees F, 0 % moisture. Discharge rated 15,000 lbs/hr; Bulk density 70; Material Flow 2/4 CFH; Temperature 550 degrees F, 0 % moisture. 197 gpm water used as heat exchange medium 95 degrees f inlet, 145 degrees discharge. Right hand drive as looking from rotary Joints.

Polymer filter continous rotary filtration system1220 SqCm active screen area9500 Cm/Hr capacity, 48000 watt oil/vapor heating capacity, with 2 heater zones. CS construction.RexRoth 11 KW power pack 3/50/500 volt 1460 Rpm. 2900 Kg Filter

LIKE NEW CONDITION! 62 hours from new. Fresh PM, incl. batteries + 2hr load test, ready to go. KD115V Skid mounted, in outdoor sound attenuating enclosure with electronic controls on day tank. Gen set manufactured by Marathon, 150 KW standby, 480 v 3ph 60Hz, Direct driven by a Volvo Penta Gen set engine. 6 cylinder 4 stroke , direct injection. Turbo Charged and air to air intercooled. Drive engine number of cylinders: 6. Batteries: Yes. Battery Charger: Yes. Controls: Yes.

• Sanitary- (1x) Down spraying, two fluid, external mixing, air atomizing nozzle APV Anhydro Compact Spray Dryer
• Air Inlet temperature 200 -300 degrees C (390-670 degrees F),
• Exhaust air temperature 90 degrees C (195 degrees F)
• Food grade construction
• Heat for hot air is natural gas fired by an Eclipse burner rated for 240,000 BTU.
• Dry product is separated in a SS cyclone, 12" top diameter x 48" high with a 4" cone bottom.
• Dust is collected in a CS bag house, 36" wide x 86" long x 14' high.16 Bags with 4" diameter x 48" long socks, approximately 64 Sq. Ft. of filtration area
• TEFC Hi efficiency. Feed pump is driven by a 0.5 HP motor. Straight wall internal is 60".

• REBUILT 2.1 cu. ft. operating capacity Jacketed Porcupine Processor designed for batch operation manufactured by Bethlehem Foundry and Machine Company
• Shell is rated for MAWP 50 PSI
• Porcupine surface area is 15 sq. ft. jacket is 9.4 sq. ft. Head flats are 3/4" and 3 & 7/8"shell is 1/4" and jacket is 5/16"
• 230/460 volt motor with a Reynolds reduction gear
• with a 207:1 ratio Steam or hot oil inlets and outlets are all 1" NPT Process inlets an are two 3" and outlets are 3.5"
• Rebuilding included the following: Unit is stripped, cleaned, and shaft and jacket pressure tested Gearbox drained, cleaned, checked and refilled. Motor replaced, unit test run. Stuffing box gaskets replaced and new rotary joint installed. New top head cover gasket replaced, Test run and painted, new coupling guard installed.
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Total Heat Transfer Surface Area: 24.4 ft². Porcupine Agitator Pressure: 150 psi. Porcupine Agitator Temperature: 600 °F. Size: 1203.

pressure -1/1.5 bar@ -25/+200 deg C

UNUSED

Internal finish 240 grit buff polished-Bright polished, external buff polish to a matte finish. ASME NB rated, and "U" stamped.

welded dish heads (2:1) 12 mm thick

Coil: 114 mm OD x 4 mm thick,

Limpet covers bottom dish and 2615 mm of straight side (pitch 150mm). Coil heating surface area.

With Insulation rings and upper drip ring. Two top lifting lugs and one tailing lug.

20" Manhole with Cover and davit arm assist, one 6" sight glass, Support Type: Lugs.

• Alloy C276 Vacuum Conical Screw Dryer.
• Coil jacket, Shell rated 88FV.
• 103" diameter x 117" length.
• Welded dished top head.
• Orbital acting screw agitation. Johnson Joint attached to top.

Pharmaceutical grade Top of belt is steam heated bottom is chilled water cooled variable speed, 0.75 kW 3/50/220/380V System equipped with SIHI cooling water vacuum pump driven by 2.5 kW 3/50/380V, 1430 RPM motor.

• Single agitator design. Trough is not jacketed Agitator is hardfaced and rated 150 psig @ 650 degree F vessel rated atmospheric @ 650 degree F Trough contains approximately 62 cu. ft. of processing space Completely fabricated and assembled except for the following: Johnson rotary joint, panel coils, drive motor, gear reduction, chain and sprocket
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)

vacuum paddle dryer with dust filter and heated shaft Order number: 14.-235/24158/00000/2-2871/53 Internal pressure rating -1/+0,5 bar @ 151 degrees C operating temperature (total volume 11.000 liter) straight side jacket pressure rated 6 bar @ 151 degrees C (volume 340 liter) Serpentine (2) 1/2 pipe coil jackets each coil rated 6 bar @ 151 degrees C (volume 50 liter); heated shaft rated 6 bar @ 151 degrees C ( volume 1120 liter) (1) bolted for shaft removal; with 3 zone jacket on straight side and 1/2 pipe coil jacket on each head Agitator shaft is 600 mm diameter and has has paddle agitators with flat blades, mechanical seals, and a rotary joint on one end for heating the shaft. Driven through a shaft mounted gear reducer Bag filter mounted on top of dryer housing. Openings include: Top - (1) 1000 mm diameter opening for bag filter, (1) 600 mm feed opening, (1) 500 mm manway with cover; center bottom outlet, 340 mm ID / 420 mm OD With Titanium Grade 2 vertical jacketed dust filter, 10 m3 (353 cubic foot) and 18 cages for filters/ socks. 1000 mm diameter x 2400 mm high, with assist top cover for sock replacement Agitation Seal Type: Mechanical. Dust Collection: Yes. Jacket Pressure: 6 bar. Jacket Temperature: 151 °C. Jacket Type: Half Pipe/Limpet.

• Can be equipped with Agitation System
• Reglassed KC series reactor body
• Manufacturers number 4364421
• With (4) side support lugs or (8) leg couplings for mounting/installation.

321 stainless steel jacket on straight side only, 4-blade turbine impellor, under belt driven by 7.5 kw, 3 phase, 50Hz, 380/660 volt, 1450/118/472 rpm SEW-Usocome geared motor, Burgmann mechanical seal, includes pipework, valves, filter, pump.

• Falling film evaporator with mechanical vapor recompression, part of a Zero Discharge System (ZLD). The Evaporator includes the following major components: the evaporator, a circulation pump, a compressor, the deaereator, a distillate system, the feed heaters, and associated pumps. Each evaporator shares a common feed tank and seeding system.
• This evaporation system was previously used in a Zero Discharge System by a major Utility company. It was designed and engineered by Bechtel, and utilizes a seed-slurry process to maintain heat transfer tubes in a scale controlled manner. The process has been maintained in excellent shape.
• The main evaporator (Plant # BC-1/2) is a Model 130T designed by RCC and manufactured by Plant Maintenance Services, and has 13,000 square foot of surface area in the tube section. The construction Alloys are Titanium, AL6XN, and 316 SS. The design conditions for the condenser shell are 8 psig internal and 2 psig external at 250 degrees F. The condenser tubes are rated for full flooding and 8 psig external at 250 degrees F. The floor and sump are rated for full flooding and 2 psig at 250 degrees F. The evaporators dimensions are 88" OD at the condenser, 106" OD in the mid section and 134"OD at the sump/skirt. Overall height is 54' 11". The unit is skirt mounted. The tubes are 2" OD x 0.028" wall thickness x 24' long with a titanium top tube sheet and a AL6XN bottom tube sheet. The vessel includes two 30" manway for top and side access, and structural steel with stairs and platforms.*The recirculation pump(Plant # P-034-A/B) is an AC/ITT single stage, open impeller, horizontal centrifugal pump. It is a model # 150, size 14 x 12 x 21 PWO, with packing on the main shaft. It is rated for 5000 GPM at 40' TDH. The material of construction is Austenitic SS (CD4MCU). It is a base mounted direct coupled pump, driven by a 75 HP AC motor. The motor is rated for 60 Hz, 3 ph, TEFC with a 497 T frame.Mechanical Vapor recompression is provided by a Roots centrifugal blower( Plant # C-002-A/B), in a skid mounted package with an electrical driver. The blower is a Type 360IB, serial # HA3352. It is rated for 1233 lbs./minute, with an inlet volume of 30,003 ACFM, at 14.82 psi, with a specific gravity of 0.622. The inlet temperature is rated for 217 degrees F and the discharge pressure is 20.2 psi. It operates at 7309 RPM. It has a Lufkin gear increaser, and is driven by a Siemens 1000 HP ac motor. The motor is rated for 3/60 1460 volts. The skid mounted unit includes controls, oil system, and oil cooler.

• Jacket conical screw mixer/dryer with top mounted filter,
• screw 7 bar @ 150 degrees C . (18.5 liter), single internal 316L (1.4404) stainless steel screw which is cored for steam heating, screw bottom driven by 11kw 3/50/380 volt 1500 rpm Eex motor, carriage motor 1.1 kw, 3/50/380 volt 1500 rpm Ex motor.
• Bottom discharge valve driven by 0.75kw, 3/50/380 volt 1400 rpm Ex motor, dished top with a 5.5 square meter 316L (1.4404) stainless steel jacketed reverse jet filter.
• Manufactured by Kilsch Apparatebau Gmbh, fabrik #2184/2, pressure -1/2 bar @ 170 degrees C (750 liter),bolt dished top, (4) jets, TUV certified

• With Lenser polypropylene non-gasketed recessed plates type KCE (51) chambers.
• 40mm cake thickness ,corner feed with 3 eye closed delivery
• 3" top corner feed, 2" 3 corner discharge.
• 3300 psi hydraulic closing pressure.
• With US Filter/Siemens air over oil hydraulic pump with a 15 gallon oil reservoir requires 80 scfm @ 100 psi air supply. Plate Thickness: 2.5 in. Plates Recessed: Yes.

• Plough share mixer without jacket rated internal atmospheric mixer included 2 choppers ,two doors for bottom discharge main V-belt drive data Main drive and gear box dismantled

Single Rotor Crusher fixed hammers. Crusher walls are 1/4" thick, shaft is 1 15/16" diameter. Unit has a SS feed chute, screen discharge with 1/2" holes230/460 volt motor.

• Class 1 Group C & D, Class 2 Group F & G Div2

gear reducer input 1,500rpm, output 71rpm mounted on a carbon steel baseplate.

w/(3) feed screws. Discharge hopper w/out valve Stirrup type hammers. Rotor belt driven by 30 HP, 3/60/230/460 volt, 1770 rpm TEFC motor. Feeder belt driven by 1/2 HP, 3/60/220/440 volt, 1140 rpm TEFC motor.

plastic 'Utiliser' dry granulator model 20-strand 321 stainless steel rotor with cutting blades motor : 50/60 Hz, 380/400/415/460/660/690 volt, 970/975/1180 rpm aluminium chamber with hinged top inspection cover