w/(3) feed screws.
Discharge hopper w/out valve
Stirrup type hammers.
Rotor belt driven by 30 HP, 3/60/230/460 volt, 1770 rpm TEFC motor. Feeder belt driven by 1/2 HP, 3/60/220/440 volt, 1140 rpm TEFC motor.

with feed hopper
serial #10 486

Eccentric vibrating mill
Type ESM Ball Mill
Usable volumn is 5 liter maximum
Total grinding tube volume is 19 liters, grinding medea volume is 15 liters
235 mm ID x 450 mm L. Unit is batch design, suitable for wet and dry grinding, with a feed grain size up to 30mm
Can accept rods, balls, and pebble grinding media, comes with CS Rods.
The Exciter is side mounted creating ellitical and linear vibrations

Underwater pelletiser system

2727 kg/hr (6000 lbs/hr)

product specific gravity 0.96 @ 25 deg C,

feed material form molten,

pellet surface moisture content nil to 0,10%

(1) Trendelkamp diverter valve, type TAV-4, serial #963620, driven by hydraulic power pack

(1) 300 sq ft 316/316L s/steel horizontal shell & tube heat exchanger, manufactured by Kenics (Chemineer), model 300-HEX-915, serial # 995893-01-01, design pressure tube side: 100 barg @ 315 deg C, shell 20 barg @ 315 deg C, jacket on heads 20 barg @ 315 deg C, (299) 12.7mm outside diameter x 2346mm long 316L tubes, single pass tube side, 324mm inside diameter 316/316L s/steel shell, tube plates are 316/316L s/steel clad, (2) 316/316L coned heads with c/steel jacket, overall length 3194mm, openings: tube side: 2-75mm, 2-50mm, shell side: 2-75mm, 1-25mm, 1-12mm, head jackets (each with) : 2-32mm, mounted on (2) fixed cradles, fully insulated and clad

(1) 3 m3/hr @ 220 deg C 316L s/steel MAAG gear pump, type Therminox TX-70/70, manufactured by MAAG pump systems, serial # 50063746, suction pressure 4 bara, discharge pressure 57-71 bara, differential pressure 57-71 bar, driven by 2-speed motor, 15 kw, 3/50/380/415/660/690 volt, 3830 rpm or 3/60/415/460 volt, 4620 rpm motor, mounted on base plate

(1) 304L s/steel Gala centrifugal pellet spin dryer with agglomerate catcher, dryer model 3016-LD, serial #981156, max product 6400 kg/hr, max water 100 kg/hr, max working temperature 80 deg C, rotor speed 780 rpm, 3-rotor screens, 2-dewatering screens, average airflow 2500 NM3/hr, easy access design, rotor is belt driven by a 2-speed motor, 5.5 kw 3/50/380/420/655/725 volt, 1440 rpm or 6.3 kw 3/60/440/480 volt, 1740 rpm, agglomerate catcher is model 9-PSG

(1) 1200mm diameter s/steel vibratory screen separator, 2-deck, model ME-48S15-6-6, manufactured by Midwestern industries inc, serial # 0399-4018, electrics 3HP, 220/380/440 volt

(1) 3420 ltr s/steel slurry base tank with 450 gpm centrifugal pump

(1) Pellet blowing/conveying unit

Control panels, pipework, filters and other ancillaries

product specific gravity 0.96 @ 25 deg C, feed material form molten, pellet surface moisture content nil to 0,10%,

system consists of:

(1) 3X 316 s/steel Black Clawson s/steel underwater pelletiser, model # 114012320, serial # 631955, internal rotary knifes, die plate with (360)

Single Rotor Crusher fixed hammers. Crusher walls are 1/4" thick, shaft is 1 15/16" diameter. Unit has a SS feed chute, screen discharge with 1/2" holes230/460 volt motor.

stainless steel (polished) Frewitt Delumper with crushing and grinding system, type Delumpwitt, upto 9000kg/hr flow rate, system includes: (1) stainless steel Frewitt Conwitt 250 conical sieve mill, serial #12014519069, internal CE 1258 Ex II 1Dckb T157 degrees C X, external CE Ex II 3D c Ex tD T125 degrees C X, (1) stainless steel infeed hopper, (1) stainless steel Frewitt crushing unit, serial #12014532028, internal CE 1258 Ex II 1Dckb T157 degrees C X, external CE Ex II 3D c Ex tD T125 degrees C X, (1) Frewitt Conwitt 250 vibrating unit, serial #1201459069, internal CE 1258 Ex II 1Dckb T157 degrees C X, external CE Ex II 3D c Ex tD T125 degrees C X, (1) servolift elevating/lifting machine, serial #12885, all mounted on a stainless steel frame

100 kg typical batch weight
(Polished to a 0.1 Ra Min finish)
Standard capacity range is 120-240 liters. This granulator features a through the wall design where the utilities are located outside the clean room. It has a jacket for the base and bowl with temperature sensor. The main impeller is capable of being raised and lowered. The side chopping system has a variable speed control.
Discharge is into a through the wall mill model U-20. Features sanitary design and Clean in place. This multipurpose machine can process dry powders, aqueous and solvent granulations, effervescent products, and melt palletization applications.
This machinery is electronically controlled. Can be used with Fluid bed dryer IPP stock # 233968.

Mikro Atomizer
Rated for 6,000 rpm.
Capable of handling capacities from 100 to 1000 lbs/hr, dependent on the material, this machine handles 3 functions in one machine. Pulverizes, air classifies and conveys the material.

1000 kg/h
120x160 mm drum screen, scraper drum 120x160 mm

attritor
Open top with welded cone bottom
Charge is 5/16" chrome plated steel (52100) shot
Operating liquid level is 185 gallons
Agitation is by a two speed Reliance 25/8.3 hp, 1800/600 rpm
AC motor through a Sym-Cyclo gearbox
With front side door for media change
Motor & drive on trolley for shaft & media changing
Insulated

continous design, rectangular bed
with two rectangular decks
with 6 x drives type WA 338 - 380 V/8,804 kW/23,6 A/50Hz.,
2 vibrating motors mfd by Rhewum,
type FX 1000-6, serial # 9212104 and # 9212105

1. siev dia. mesh approx 6mm x 6mm, 2250mm long x 950mm wide, 2. siev dia. mesh approx 2mm x 5mm, 1350mm long x 950mm wide, 1. screen cloth dia. 1000mm wide x 1540mm long, 2. sceen cloth dia. 1000mm wide x 2540mm long, 3. screen cloth dia. 1000mm wide x 2440mm long, material of sieves and screen cloths is 1.4301.
   Motor data: 220-380 V/4 kW/50 Hz/ 980 rpm by 5370 kg centrifugal force, total weight 2800 kg.

inlet Carbon Steel skid mounted High Efficiency Fine classifier
3600 RPM rotor max speed.15kW.
460 vac
35 amps
Inlet size is 9", outlet is 21" x 19 " square flange. Rejects line is 5"
Particle wheel has hinged door for clean out and wheel access
This classifier is rated for 2000-2600 m3h, and 200/2400 kG/h
Finess is rated for 3.0-4.0 (c/37um).

AB (Sweden)
2 deck vibratory screen
size 0.9 x 2.25
(2) vibratory motors, type VV40B/4
(1) motorised rotary lock valve

RECONDITIONED,
Approximately 25 - 30 tonnes of material per hour (dependant on density) cast steel Briquetter
very similar in design to Sahut Conreur and Komerak Greaves
Roller size: 1.2m diameter, 925 Ovoid type briquettes per revolution
briquette size approximately 45mm diameter x 35-40mm thick
Twin hydraulic rams
80 tonnes a piece (2500 psi)
each side gives a separating force of 320 tonnes
English electric main drive motor
with a fluid coupling to a two speed W.G.W inline gearbox. Two speed 8.5 or 11 Rpm (at the rolls)
Machine has undergone a full refurbishment and is in full working order:
As part of the refurbishment the following was done:
Gearbox rebuilt and gears refaced where necessary
Reconditioned fluid coupling
Reconditioned main drive motor and feeder unit motor
New Gearbox oil circulation pump
Fresh oil in gearbox and transfer box
All new hydraulic lines and couplings
All four rams are refurbished
New safety valves and couplings fitted to the hydraulic power pack
Main Bearings disassembled, checked and re-greased (all OK), new lube points/grease nipples installed
Main roll surfaces polished and checked
Feeder unit was stripped and checked, feed control gates greased.
Reconditioned feeder unit motor
Fully blasted undercoated and painted
Custom made stand as shown
Also a custom made out feed hopper to attach to the stand and machine.

single screw extruder line
General purpose screw and feed hopper.
Production rate: 75 Kg/hr maximum polypropylene.
Barrel has (8) heaters with (3) electric fans
Extruder driven by a 60 HP (46 KW) DC motor. Line is complete with a15' long x 12" wide x 8" deep stainless steel cooling bath with air knife and (1) automatic 100mm granulator, Type ASG-10, serial #00-015-2204. Driven by 2.2 KW motor. Extruder is complete with control panels.

10 HP
Fixed knives blunt one side, w/reversible rotor.
Unit driven by approx 10 HP, US varidrive. Screw feed driven by 1/4 HP, 3/60/230/460 volt US varidrive
3/60/230/460 volt
US varidrive.

spiral air classifier
coarse material removal driven by 2 kw, 3/50/660/1450 rpm EX motor
mounted on a baseplate

150mm deep deck
950 rpm
Exe II T3 vibratory motors
stainless steel coned top cover,

Alexanderwerk Pharma
pressure internal -1/3 bar @ 145 deg C (91ltr), jacket -1/3.3 bar @ 145 deg C (13ltr)
underdriven by a DIETZ
400-690 Volt

2 deck vibratory screen
(2) vibratory motors
(1) motorised rotary lock valve

63mm,
single screw extrusion line,
approx 60 kg/hr of 800mm wide plastic sheet),
line consists of: (1) Bone Brother 63mm x 2m long c/steel single screw extruder,
motor with cooling fan,
barrel with (5) fans driven by 0.33 kw, 3/50/415 volt, 2800 rpm motors,
126mm x 38mm feed opening with s/steel feed hopper,
(1) 3-roll calender, rolls 300mm diameter x 800mm long, rolls with mirror finish, each roll is oil heated with its own oil heater, each roll gap adjuster has a hydraulic ram driven by 4 kw, 3/50/380-420 volt, 1435 rpm motor vai a Eurodrive gearbox,
the calender is mounted on a moveable skid , skid has a hydraulic raise/lower mechanism, (1) end of line Gillard & Co sheet cutter, mounted on wheels, totally enclosed in a cabinet, system with control panels.

• Hammermill Disintegrator 18" diameter rotor with 32 hammers.

• centrifugal screen. 3/60/230/460V Sifter cylinder has two cleaning doors 3" x 8".Totally enclosed high - capacity centrifugal scalper for chemicals, food and a wide range of powder material.The rotating paddles break up soft agglomarates and propel individual particles through the screen while rejecting hard lumps.

attritor
Size 100S
30" deep tank, with 2 1/2" dia shaft, (6) cross bars.
Canter lever tilt mechanism
7 1/2 HP Class I, Div II drive.

Wet Grinding Media Mill
water cooled grinding chamber
Batch size 200 to 1000 liter capacity
closed design grinding chamber,axial flow. Mechanical Seal on shaft, with Teflon grinding discs for agitating the grinding media
50 HP motor, 3/60/230/460 volt Class1 Groupd D