Used Porcupine dryers for sale: indirect thermal dryers for sticky or viscous materials

• REBUILT 2.1 cu. ft. operating capacity Jacketed Porcupine Processor designed for batch operation manufactured by Bethlehem Foundry and Machine Company
• Shell is rated for MAWP 50 PSI
• Porcupine surface area is 15 sq. ft. jacket is 9.4 sq. ft. Head flats are 3/4" and 3 & 7/8"shell is 1/4" and jacket is 5/16"
• 230/460 volt motor with a Reynolds reduction gear
• with a 207:1 ratio Steam or hot oil inlets and outlets are all 1" NPT Process inlets an are two 3" and outlets are 3.5"
• Rebuilding included the following: Unit is stripped, cleaned, and shaft and jacket pressure tested Gearbox drained, cleaned, checked and refilled. Motor replaced, unit test run. Stuffing box gaskets replaced and new rotary joint installed. New top head cover gasket replaced, Test run and painted, new coupling guard installed.
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Total Heat Transfer Surface Area: 24.4 ft². Porcupine Agitator Pressure: 150 psi. Porcupine Agitator Temperature: 600 °F. Size: 1203.

• Single agitator design. Trough is not jacketed Agitator is hardfaced and rated 150 psig @ 650 degree F vessel rated atmospheric @ 650 degree F Trough contains approximately 62 cu. ft. of processing space Completely fabricated and assembled except for the following: Johnson rotary joint, panel coils, drive motor, gear reduction, chain and sprocket
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)

• 12" diameter-ASME stamp for Jacket Only Link Belt HP rated 10’
• Vessel rated for 3psi +/- (vacuum)
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Porcupine Agitator Pressure: 50 psi. Porcupine Agitator Temperature: 300 °F. Size: 1208.

• This Porcupine has a barometric separating chamber, which allows dust to settle out of the water or other vapor generated in drying.
• Processor Single agitator design Agitator 12" diameter, 7' long.
• Heating medium hot oil or steam Vessel rated 15 psig and full vacuum @ 320 degree F, jacket rated 75 psig @ 320 degree F, agitator rated 75 psig @ 320 degree F.
• Working volume is 4.4 cubic feet Agitator has 29 square feet of heating area and jacket 15 square feet.
• With direct coupled gear reducer and motor.
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Total Heat Transfer Surface Area: 44 ft².

• UNUSED One agitator.
• Jacketed trough
• Completely fabricated and assembled except for the following: Johnson rotary joint, drive motor, drive gear and coupling
• No cover, agitator 35 sq.ft. trough 55 sq.ft.
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)

rotating segmented disc dryer
316 stainless steel (1.4571) single rotor with segmented discs and rotary coupling
via reduction gearbox
mechanical seals on shaft
bolted ends
drive end
top inlet with stainless steel filter
fabrik TRF005/043
TUV certified

Buss-SMS
continuous rotating segmented disc dryer
3.9 square meter
rotor -1/20 bar @ 300 degrees C (22 liter)
total useable heating surface 10.7 square meter
heated by steam
single rotor with segmented discs and rotary coupling
via reduction gearbox
mechanical seals on shaft
bolted ends
top inlet with s/steel lump breaker

• Single agitator
• Agitator 12" diameter and 7' long
• Heating medium hot oil or steam
• Vessel rated 15 psig @ 320 degree F
• Agitator has 30 square feet of heating area and with jacket added 15 square feet additional.
• Working volume 4.4 cubic feet.
• Outboard bearings.
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)

• Agitator 12" diameter, 3' long
• Heating medium is hot oil or steam
• Working volume 1.89 cubic feet
• Vesssel rated 15 psig and full vacuum @ 650 degree F, jacket and agitator rated 150 psig @ 650 degree F
• Agitator 12.4 square feet of heating area, jacket 7.3 square feet
• via a gearbox
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Total Heat Transfer Surface Area: 19.7 ft².

• Heating medium is hot oil or steam
• Working volume 2.10 cubic feet
• Agitator 15 square feet of heating area and 9 square feet on the jacket
• Full vaccum
• Vessel rated 50 psig and full vacuum, jacket and agitator rated 150 psig 600 degree F
• Working volume 2.10 cubic feet
• Agitator 15 square feet of heating area and 9 square feet on the jacket
• 3/60/220/440 volt varidrive with UL label
• 5.4 to 54 rpm output
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Total Heat Transfer Surface Area: 24 ft².

• Single agitator design
• Heating medium is molten salt (electric)
• Vessel rated 15 psig @ 1000 degree F, agitator rated 150 psig @ 1000 degree F
• Working volume 2.10 cubic feet
• Agitator 15 square feet of heating area and 9 square feet on the jacket
• Motor: 3 phase
• Reducer 87:1 ratio
• On CS frame
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Total Heat Transfer Surface Area: 24 ft².

• Material of construction 316SS (18% CR, 11% nickel)
• Working volume 1.89 cubic feet
• Heating medium is hot oil or steam.
• Full vaccum
• Agitator 12.4 square feet of heating area
• jacket 7.3 square feet
• Outboard bearings
• Packing gland on shaft
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Total Heat Transfer Surface Area: 19.7 ft².

• Heating medium is hot oil or steam
• Vessel rated 20 psig and full vacuum
• Working volume 2.10 cubic feet
• Agitator 15 square feet of heating area and 9 square feet on the jacket
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)

• Trough only
• Porcupine Processer Agitator 72.9 sq. ft. heating area Panel coils jacket to be applied and will add 36.6 sq. ft. of heater area
• Trough working volume is 14.9 cu. ft. per batch
• Agitator has pusher/scraper clips center discharge
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)

• porcupine processor Unit has 2.10 cu ft operating volume
• 15 sq ft porcupine surface 9 sq ft jacket surface
• Should be a candidate for scrap
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)

• TROUGH ONLY
• endplates are CS
• Total heat transfer area is 286 sq.ft. on the trough.
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)

• Agitator 12" diameter, 3' long. (18% Cr, 11% nickel)
• hot oil or steam and full vacuum
• Working volume 1.89 cubic feet
• Jacket 7.3 square feet
• (requires motor and gear drive)
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Total Heat Transfer Surface Area: 20 ft². Total Working Volume: 1.89 ft3. Size: 12" diameter x 36" long.

• This one probably requires a lot of work
• 223 sq. ft. of heat area on the agitator 102 square feet on the jacket
• Original design speed 10 rpm Pitch angle of agitator is 1 degree
• Trough width is 30"length is 218"with 62.1 cu ft of operating capacity
• product discharge is drive side bottom
• 30" high x 14" wide Plate coil jacket on exterior of trough manufactured by Dairy Equipment CS construction rated for 150 psi at 650 degrees F(SN # 15914-3 built 1991)Agitator is sealed by packing, has a rotary joint type SNH One lid is available, unit requires 4
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)

• Rated for Full Vacuum internal
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Total Heat Transfer Surface Area: 474 ft². Porcupine Agitator Pressure: 75 psi. Porcupine Agitator Temperature: 300 °F. Total Working Volume: 90.8 ft3. Size: 4210. Shaft is Cored ?: Yes.

• Good candidate for refurbishment
• 30" diameter--Last operated at 80 lbs/ft3 bulk density, previously processing 420 ft3 per day. (except the last 5’ of agitator is Inconel 625 )Continuous feed with bottom discharge recycle screw. 177 sq. ft. of heat transfer surface area on the agitator, and 266 sq. ft. of heat transfer surface area on jacket. Packed stuffing box assemblies seal the shaft, hardened removable wear sleeves on the shaft seal areas to extend the shaft life Hot oil Johnson joints on the agitators non drive end. Agitator chain driven by 20 hp explosion proof motor at 5 rpm through a reducer. Bottom discharge with a fixed weir. Last operated at 80 lbs/ft3 bulk density, previously processing 420 ft3 per day.
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Total Heat Transfer Surface Area: 443 ft².

• Heating medium hot oil or steam
• Vessel rated atmospheric @ 550 degree F,
• jacket rated 150 psig @ 550 degree F,agitator rated 75 psig @ 550 degree F
• Working volume is 5.2 cubic feet
• Agitator has 35 square feet of heating area and jacket has 20 square feet
• Clipps need to be cut off and re welded in the correct position
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions) Size: 1208.

• 30" dia x 16' long twin shaft porcupine processor
• Vaportight trough
• Both Rotors have a combined 392 sq ft of heating surface
• Approximately 140 cubic foot trough capacity
• Trough not jacketed
• Shaft speed 14 rpm
• UL label
• 30" vapor outlet on top cover, 12" x 12" feed port, 13" x 19" quick opening inspection door, 8" bottom clean outside discharge
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)

• With drive and panel coils utilizing steam as the heat transfer medium agitator is ;142 sq. ft Trough is; 208 sq. ft
• The working volume is, 39.3 cu.ft It has a single shaft design supported by pillow block bearings with packing glands on shaft output rpms, 37 Ratio:48:11 service rating HP= 35.1
• Motor:80/40 amps3 phase AC electric motor Trough heating by four separate Tranter plate coils designed for 150 psi at 375 degrees F All have 1" inlets and outlets with weld neck flanges Serial and NB numbers are a follows: NB # 22173-SN PC13125; NB # 22174 SN # PC13126, NB # 22176 SN # PC 13128, NB # 22175 SN # PC 13127
• Bottom opening *' valve with Jamsbury automatic actuator Steam lines to rotary joint are 1.5" inlet & outlet
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)

• Spare trough Size 54-16
• Shell rated for 5 psi at 325 degrees F Capacity of trough is 213 cu.ft
• Twin rotor chamber 36" deep x 191" long
• Designed to use two screws
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)