Heat Transfer & Thermal Processing - Used and Surplus Inventory | IPP

• Three pass fire tube boiler5021 MBHMBH input 6278Fireside heating surface area is 750 sq. ft Firing rate is as follows: 1000 BTU Gas (MBH) =6277, 140,000 BTU/Gal. Oil (GPH) =44.8Safety valve rated for 6000 psi Boiler has 182, two inch tubes This boiler features FGR and low Nox operation with it's IRI gas train While firing natural gas, emissions levels are are no greater than 30 PPM of NO x This boiler features 3 gas passes that extract the maximum usable heat from the fuel while maintaining optimum flow for forced draft firing It also has easy opening/closing doors that minimize labor and parts cost’s while performing routine maintenance such as cleaning and inspections Water requirements are 6551 pounds of water or 785 gallons Approximate weight wet is 16,251 lbs., approximate dry weight is 9,700 lbs.

• Alloy C276 Vacuum Conical Screw Dryer.
• Coil jacket, Shell rated 88FV.
• 103" diameter x 117" length.
• Welded dished top head.
• Orbital acting screw agitation. Johnson Joint attached to top.

Vacuum dryer system internal pressure rated -1/+1bar @ -10/+165 degrees C (volume 250 liter), jacket pressure rated -1/+8bar @ -10/+165 degrees C (volume 35 liter) type CD180M-4 3~/50Hz/230-400V/1,460rpm CE confirm, EExdeIICT4, system including: (1) 3.1m² 1.4571 stainless steel tube and shell heat exchanger/condenser, (1) 8m³/h @ 3m head iron cast centrifugal pump, (1) 50 liter 1.4571 stainless steel condensate receiver, (1) 20 liter 1.4571 stainless steel gas separator, (1) 17.5 liter 1.4571 stainless steel jacketed pressure tank, (1) Frequency converter on pallet, (2) stainless steel guards on pallet, (2) Valves and (1) chain on pallet, Accessories on pallet Jacket Temperature: 165 °C.

Twin Shaft Nara paddle Shell WO Number DS-220, Jacket Serial Number D-258, National Board Number 1102. Heat Transfer area: Jacket 107 Sq Ft, Agitator 293 Sq Ft, total 400 Square Foot. twin shaft with discontinous wedge shaped staggard paddles. Both jacket and agitator rated for 165 psi at 425 degrees F. Indirect heat, by saturated steam heat; rotary joints on shafts with quick disconnects and zero speed switch on end of shaft. Shaft seals are Meco Systems self-aligning externally adjstable, fully split elastomer seal, with purge port. With a 316LSS dome type covered trough rated for 5 psi pressure. With a chain and sprocket drive, SEW Sanasaio Parallel shaft speed reducer and a 75 HP Reliance motor. Motor data, ID # OIMAN 79345 G001 BC Frame 365 T, rated for 1780 rpm, Volts 230/460 amps 172/86 3 ph, Hz 60. Shaft speed approximately 12 RPM. Openings include: 15" x 36" feed opening, (1) 12" diamter vapor opening, (3) 18" x 24" explosion vent openings, (1) 6" Sweep Gas Inlet, (1) 20" x 20" Access hatch with bolted cover, (2) 6" view ports; trough has (1) 12" x 58" flanged discharg opening, (2) externally adjustable weir gates.

Electric air dryer 12 hr dryer cycle 3.6 KW W/50 scfm Nash Mdl AL-574 compressor 10 HP, 3480 rpm motor

Built in Economizer.

NFPA class A drum warming oven. designed for BOC Anhydride and acetic acid Purge time 10 minutes input 124,000BTUH at 75 psi Complete with fire protection and controls.

• Rotary Vacuum Paddle Dryer with heated shaft.
• Vessel rated for Full vacuum internally.
• With 316 stainless steel internals & stainless steel half-pipe coil jacket.
• One head bolted dished, one head welded dished.
• Unit has approx.12" diameter heated shaft with paddle agitator blades.
• Shaft is direct coupled to a gear reducer
• Openings include: (1) 18" Top, (1) 12" x 16" end port with hinged cover, Bottom center discharge.

normal working pressure 83 bara, flue gas for dimensioning 16,667 Nm3/hr, flue gas temperature after economizer 139.5 deg C, content of CO2 in flue gas 8.92 volume %, H20 15.84 volume %, O2 2.07 volume %, net calorific value 42.8 MJ/kg (gas oil), 39 MJ/kg (natural gas), Saacke type TSAAYD-135-E3-6275 steam atomizing burner, designed for natural gas or gas oil, heat input 22,000kg/hr, gas oil output 190-1329 kg/hr, natural gas 163-1631 Nm3/hr, energy input 13.1 MW, fuel input natural gas 1206 kg/hr, gas oil 1097 kg/hr, air flow 14,000 Nm3/hr, flue gas flow natural gas 14,150 Nm3/hr, gas oil 14,866 Nm3/hr, heating surface area furnace 60sqm, screen 2.6sqm, evaporator 33sqm, walls of convection part 25sqm, economizer 1 683sqm, economizer 2 78sqm, total 881sqm the boiler is an all welded water tube boiler with natural water circulation, built as a vertical and self-contained construction in which the downcomers form the supporting columns, vertical expansion of the boiler is free upwards, boiler has a radiation part, a convection part and a detached economizer, the radiation part is to reduce the flue gas temperature before the convection part, the radiation part is built as an all-welded membrane wall section on the sides, top and partition wall, the economizer is in the back of the convection part and is made with horizontal tube coils, these are a nest of pipes consisting of 14-tube lines of each 28 tubes, the evaporator is made with diagonal tube coils, which are a nest of 6-tube lines of each 28 tubes, the detached economizer is built as a four sided casing tower in which are placed horizontal convection heating surfaces, boiler includes: (1) 1640ltr c/steel boiler drum, steam space load 275 m3/m3xh, 1200mm diameter x 3m long, 40mm thick, weld dished ends, (1) Detached in-line fin tube Economizer, manufactured by Emvertec, 683sqm, design pressure 13.5 bar, (1) 316 s/steel Deaerator vessel, manufactured by Cool Technology ltd, design pressure 2 bara @ 105 deg C, operating pressure 0.21 bara (3) Feed water pumps, manufactured by KSB, type HGM-2/15, Other associated equipment include fans, valves, pumps, instruments, control panels, etc

• 148 Sq. ft Heat Exchanger (2)

• Water Sterilizer unit has (2) sterilizer heat exchanger tubes mounted in a frame .

• Tube A: National board number 2810, serial number 37173/1,Rated 116 psi @ 347 degrees F both sides;

• Tube B: National board number 2811, serial number 37173/2,rated 116 psi @ 347 degrees F both

  sides.

• 120 straight tubes

• Sanitary- (1x) Down spraying, two fluid, external mixing, air atomizing nozzle APV Anhydro Compact Spray Dryer
• Air Inlet temperature 200 -300 degrees C (390-670 degrees F),
• Exhaust air temperature 90 degrees C (195 degrees F)
• Food grade construction
• Heat for hot air is natural gas fired by an Eclipse burner rated for 240,000 BTU.
• Dry product is separated in a SS cyclone, 12" top diameter x 48" high with a 4" cone bottom.
• Dust is collected in a CS bag house, 36" wide x 86" long x 14' high.16 Bags with 4" diameter x 48" long socks, approximately 64 Sq. Ft. of filtration area
• TEFC Hi efficiency. Feed pump is driven by a 0.5 HP motor. Straight wall internal is 60".

• Single agitator design. Trough is not jacketed Agitator is hardfaced and rated 150 psig @ 650 degree F vessel rated atmospheric @ 650 degree F Trough contains approximately 62 cu. ft. of processing space Completely fabricated and assembled except for the following: Johnson rotary joint, panel coils, drive motor, gear reduction, chain and sprocket
• Manufactured by Gale Process Solutions (legacy Bethlehem Corporation/Advanced Thermal Solutions)

Niro (Bowen Design) Spray Dryer With BB-3 Type Spray machine Conical Bottom drying chamber is 12' diameter x 6' 7" straight side, and utilize a co current air flow design. Elevation to top of dryer is 25' 7". This is a complete system with the spray dryer and bag house mounted out doors. Feed related equipment is mounted indoors on a skid. Dryer details are as follows: Supply air; 1385 acfm. Natural gas; 27.9 acfm. Feed; 1725 lbs/hr. Product 525 lbs/hr. Evaporation rate 1200 lbs./hr. Process gas inlet temp. = 1100 degrees F. BB-3 spray machine with complete controls including a Penthouse control panel, feed valve, automatic force oil lube system by Sloan Brothers, and Magnetek GPD 505 VSC variable motor speed system. Bag house is manufactured from 321 SS, rated for 400 degrees F, with an air volume of 1850 scfm, and air to cloth ratio of 3.9:1. Blower is CS, by New York blower, series 45, size 224 and rated for 3000 cfm at 3127 rpm. Other support equipment includes a 400 gallon, fiberglass mixing feed tank, and related pumps. Auto valves are by Fischer, instrumentation is by Rosemount.

Jacketed rotary vacuum batch paddle dryer with static chopper blades Patent and designed by List DTB manufacturing #3000.01.01.01.3000, working pressure internal -1/6 bar @ 260 degrees C (11000 liter), jacket 6 bar @ 260 degrees C (511 liter), shaft 6 bar @ 260 degrees C (560 liter), bolt flat ends, 316Ti stainless steel (1.4571) half pipe coil jacket on straight side and both ends, paddle driven by a 110/112w, 3 phase, 50/60 Hz, 400-690/460 volt, 1488/1791 rpm, IP 55 siemens CE motor via a Flender 906/9.4 rpm reduction gearbox paddle speed 9.4 rpm openings top: 1-800mm (filter), 4-250mm, 4-150mm (product inlet), 2-150mm, 2-50mm, 4-50mm (jacket), side: 8-50mm (jacket), bottom: 1-150mm (center discharge), 1-80mm, 4-50mm, both flat ends: 2-50mm (jacket) dryer with dust filter, cyclone Dust Collection: Yes. Jacket Material: Stainless Steel Austenitic. Jacket Pressure: 6 bar. Jacket Temperature: 260 °C. Jacket Type: Half Pipe/Limpet.

GMP grade sanitary stainless steel construction order number V4635 vibration bed is belt driven electrical motor : type D160LA-6 , ExII3G, EExIIT4 system included with (1) 7m³ (1.4571) stainless steel silo manufactured by Scholl Switzerland AG order number 502838 serial number 201282 pressure rated -0,1/0,6 bar @ -20/120 degrees C (total volume 7100 liter) openings on top: (3) DN40, (1) DN50, (1) DN80, (1) DN100, (1) DN200, (1) DN500 manway cover; with (1) 4500 m³/h (1.4571) stainless steel radial fan manufactured by Reitz type KXE100-008030 serial number 166417 shaft rating maximum 20.17kW @ 3000rpm with frequency converter fan is coupling driven by a 37kW electrical motor, manufactured by Felten & Guilleaume, type CD200L2-2, serial number 415274001H, 3~/50Hz/400-690V/2955rpm, ExII2G, EEXdeIICT4, mounted on carbon steel baseplate; with (1) 1.2m² (1.4404) stainless steel plate heat exchanger, manufactured by Barriquand, type IJS, serial number 26361E, pressure shell side 2bar @ 200 degrees C (volume 16 liter), pressure plate side -1/6bar @ 200 degrees C (volume 2 liter), openings plate side: (2) DN25, openings shell side: (2) ½” (2) DN80; with (1) 44.3m² (1.4404) stainless s teel plate heat exchanger, manufactured by Barriquand, type IJMASC, serial number 26362E, pressure shell side 2.9bar @ -35/100 degrees C (volume 335 liter), pressure plate side 10bar @ -35/50 degrees C (volume 165 liter), openings plate side: (2) DN80, openings shell side: (1) DN25, (2) DN250; with (1) 12.7m² (1.4404) stainless steel plate heat exchanger, manufactured by Barriquand, type IJS, serial number 26359E, pressure shell side: 2 bar @ -20/200 degrees C (volume 190 liter, pressure plate side: -1/6bar @ -20/200 degrees C (volume 25 liter) openings plate side: (2) DN50, openings shell side: (2) ½” (2) DN250; with (1) 3.6m² (1.4435) stainless steel shell and spiral tube condenser, manufactured by Züricher Apparatebau, order number 105074, serial number 242, pressure tube side: 7.8bar @ -30/200 degrees C, pressure shell side: -1/6bar @ -30/200 degrees C, 500mm diameter x 1039mm length; with (1) 6m² (1.4404) stainless steel shell and tube condenser, manufactured by Züricher Apparatebau AG, order number 502637, serial number 1789, pressure shell side: -1/6bar @ -45/200 degrees C (volume 74 liter), pressure tube side: -1/8bar @ -45/200 degrees C (volume 45 liter), openings tube side: (2) DN50 (1) DN100, openings shell side: (2) DN40; with (1) 4.7m² (1.4404) stainless steel plate heat exchanger, manufactured by Barriquand, type IJS, serial number 26360E, pressure plate side: -1/6bar @ -20/200 degrees C (volume 8 liter), pressure shell side: 2bar @ -20/200 degrees C (volume 102 liter) openings plate side: (2) DN25, openings shell side: (2) ½” (2) DN150; with (1) 4m³ (1.4435) stainless steel vertical agitated tank with half pipe coil jacket, manufactured by WAFAG, order number 89536, serial number 8379, pressure inside: -0.32/4bar @ -30/200 degrees C (volume 4340 liter), pressure jacket side: 7.5bar @ -30/200 degrees C (volume 176 liter), with a (1.4571) stainless steel 3-blade propeller agitator, order number 503049, with mechanical seal, manufactured by Burgmann, type M481K-D20/60, pressure -1/16bar @ -30/200 degrees C, with 3 liter lubricator, manufactured by Aerni, type A-139, pressure 26bar @ 200 degrees C, agitator is driven by a gear, type RXF97D4/P, gear is belt driven by a 7.5kW electrical motor, manufactured by ABB, type 132M-4, 3~/50Hz/400V/1450rpm, EExdeIIBT4, openings top: (1) DN500 including (2) DN100 sight glasses, (1) DN600 including (2) DN50 and (1) DN300, (2) DN100, (3) DN200, openings bottom: (1) DN65, openings half pipe coil: (2) DN40, mounted on (4) lugs; with (1) 316L stainless steel vertical cyclone separator, manufactured by Ventilex, order number 502845, openings top: (3) DN25, (1) DN200, (1) DN300, openings side wall: (1) DN300, with cone bottom, mounted on (4) lugs; with (1) 14m³/h by 20m head (1.4408) stainless steel caned motor pump, manufactured by Ruetschi, type SMN-G5-160SR5E16-2V, order number 502627, driven by a 5.6kW electrical motor, type SR5E16-2V, 3~/50Hz/400V/2930rpm, EExdeIICT4; with (1) 2000mm diameter (1.4404) stainless steel vertical dust filter, manufactured by Ventilex, order number 502846, bolt dished top and weld dished cone bottom, 2000mm diameter x 3000mm straight side (4580mm overall length), (52) 316L stainless steel inlets, 145mm diameter x 2500mm length, openings top: (2) DN25, (3) DN100 sight glass, openings side wall: (2) DN300, (2) DN 200 sight glass, (4) DN50, (8) DN15, (7) 1”, opening cone side wall: (1) 500mm diameter manway cover, opening bottom: (1) DN200, mounted on (2) lugs; with (1) 316L stainless steel discharger valve, manufactured by Matcon

continuous vibrating fluid bed dryer perforated fluid bed openings: feed: 1-600mm, powder discharge: 1-300mm, top: 1-750mm manway, 1-450mm, straight side: 3-450mm manways, bottom: 2-625mm each with a 625mm diameter x 980mm straight side s/steel tank dryer mounted on carbon steel frame with springs

• Gouda Cooling Disc Crystallizer
• Internal plated for crystallizing the product, with wipers driven by the rotating shaft.
• Body OAL(no Motor or shaft) 118" long x 82" high x 60" wide.

• size OD-324,
• rated heat load 38.47kw
• design pressure tube side 10 barg + full vacuum @ -29/185 degrees C,
• shell side 10 barg + full vacuum @ -29/185 degrees C,
• 2- 316L stainless steel flat bonnet heads,
• (19) internal 316L stainless steel baffle plates,
• CE0040
• design code PD 5500 (2000) CAT 2 PER (1999) MODULE G CAT II Length: 2,900 mm. Tube-side Passes: 8. Tube Type: Straight Tube. Tube Number: 152. Tube Diameter: 12.7 mm. Tube Length: 2,400 mm. Tube Thickness: 1.65 mm. Nozzle Schedule: openings tube side 2-50mm, shell side 2-100mm.

• N2 Vaporizer, ambient air vaporizer for cryogenic applications.
• Ambient air vaporizers require only the heat transfer between the product & the outside air. No need for fans, heating, hot water, steam, compressed air, etc.
• Zero Moving Parts: reliable construction with minimal failure points.
• Rated 500 PSI, Manufactured by Finnco
• 20,000 SCFH, service to -425 degrees F.
• 24 center-bored aluminum extrusions with 8 fins each.
• Arranged in frame with legs, mounted in 6 x 4 array with extrusions equally spaced.
• 1.5" inlet/outlet flanges.
• Start-Up Pressure Drop: 2.5 psi.
• Operating Pressure Drop: 1.8 psi.

jacketed rotary vacuum paddle dryer Internal design pressure: -1/6 bar @ -10/150 degrees C (10180 liter) Coil jacket: 6 bar @ -10/150 degrees C (500 liter) Rotor/paddle: 6 bar @ -10/150 degrees C (300 liter) (1) bolt flat end (drive), (1) clamped flat end, rotor/paddle with union joint and cored for steam heating, rotor/paddle driven by approx 100kw motor via a gearbox center bottom discharge Jacket Pressure: 6 bar. Jacket Temperature: 150 °C. Jacket Type: Half Pipe/Limpet.

Missing 4 pans

• design pressure internal 4 bar + full vacuum @ -29/185 degrees C,
• jacket 10 bar + full vacuum @ -29/185 degrees C,
• shaft 10 bar + full vacuum @ -29/185 degrees C,
• shaft driven by 22/15kW, 3/50/415 volt, 1465/980 rpm IP55 motor via a 24.20:1 ratio gearbox,
• half pipe coil jacket on body and ends
• center bottom discharge,

dryer with

(1) (1) 150 liter 316L stainless steel pressure tank (jacket expansion tank), pressure -1/6 barg @ 185 degrees C,

(1) 316 stainless steel centrifugal pump, manufactured by Girdlestone, type 12CS3G, serial #53534, size 80-50-175, driven by 11kW, 3/50/415 volt, 2940 rpm EEx de IIB T4 motor, mounted on a baseplate, Dust Collection: Yes. Jacket Material: Stainless Steel 316L. Jacket Pressure: 10 bar. Jacket Temperature: 185 °C. Jacket Type: Half Pipe/Limpet.

jacketed rotary vacuum paddle dryer safe operating pressure of vessel atmospheric/vacuum 3000 liter with rotary union joint top mounted dust filter, bottom discharge with valve,

Note: Drawings show Mills, we did not get some of them. Suitable for installation in Hazardous areas.
Typical working volume is 30-225 liters based on the allowable product density of 1500 kg/m This fluid bed dryer was designed for Pharmaceutical service and features sanitary design and clean in place With wet and dry loading ports, internal lighting, and sample ports Air handling is custom manufactured by ZAir, Type SKG-4 Manufactured of 316 SS construction This unit is complete with all filters, and accessories High shear granulator (IPP Stock # 233969) is available at additional cost. 100 kg