Environmental & Pollution Control from IPP. Over 75 pieces for sale. Chemical Equipment and Process Equipment buy unused, surplus, second hand or used here.

Downflow dust collector
500 to 3,150 CFM air flow
With 4 filter cartriges
Housing has a hopper bottom with a manual valve designed to discharge into a pail
3600 rpm blower
3/60/230/460 motor
Includes Torit digital controls

Vapors handled: NH3, N2, toluene vapor, 100 #/hr HCL, 180 #/hr SOC12 vapor

• Vapors handled: NH3, N2, toluene vapor, 100 #/hr HCL, 180 #/hr SOC12 vapor

• reverse jet filters,
• 600 liter capacity chamber
• weld dished top
• unit has 10 x filter elements
• max operating pressure 6.2 bar @ 60 degrees C, min operating temperature -30 degrees C,
• filter with carbon steel fan
• design pressure 6.9 bar
• filter with carbon steel fan, manufactured by Turbovent, type VR25L-1343000, serial #22442, driven by a 2-speed motor,7.5 kw, 3/50/400-690 volt, 2915 rpm or 9 kw, 3/60/440/480 volt, 3510 rpm, openings side 1-450mm inspection port, 1-75mm, bottom 1-500mm discharge,
• unit mounted on carbon steel skid,

with blower and controls
With Blower mounted on the side of the filter housing rated.
@ -40 to +30°C, single effect, filter resistance 8 mbar
with cone bottom for discharge
EEX rated
Operating Voltage 230/400
Control panel mounted on side.
Mounted on 4 legs.
CE-certified.

• built to reduce the total NOX to 200mg/m3 of total gas flow as NO2 at fan discharge
• inlet gas flow 138.1 m3/hr
• inlet temperature (10 - 25 degrees C) say design normal = 20 degrees C
• liquor acidification composition 36% CO2 64% N2
• Azide destruction composition 18% NO2 and 82% N2
• Nitrate destruction composition 36% NO2 and 64% N2
• an additional 180m3/hr gas flow into stage 2 tower during purging
• an additional 66m3/hr minimum of oxidation air is added at stage 1 tower inlet
• design code BS4994: 1987 CAT 1
• 10780 liter capacity,
• (2) 1m diameter x 3477m total height Polypropylene lined packed columns, manufactured by Hat International Ltd, design pressure -0.1 barg @ 50 degrees C, bolt flat top, internal spray nozzles, packing is 2 x 1.65m3 of Lanpac 3.5", 2.1m packing height
• (1) Polypropylene lined rectangular holding tank, approx 3.8m long x 1.2m wide x 1.2m high, flat top and bottom,
• (1) 1000 liter Epoxy vinyl Ester resin vertical caustic dosing tank, bolt dished top, weld flat bottom,
• (1) 220/264liter capacity stainless steel dosing pump, manufactured by ProMinent Fluid Control UK Ltd, serial #2007007687, 7 bar pressure, Ex II 2GD IIC T4 x, driven by approx 0.75kW motor,

Water Softner

multi-effect WFI water distillation unit.
All sanitary construction
Unit has 5 distillation columns, all national board rated,
145 psi @ 14 to 362 degrees f in the shell; 145 psi @ 14 to 362 degrees f in the tubes.
circulation pumps

Column is 4 sections bolted together. (bottom section is IPP # 246702) Price includes bottom section 246702
Packing is Norton 316L SS 1" pall Ring "Hy-Pak", support assemblies are Norton #818 and Liquid distributer is Norton # 845.

Down flow design
(6) bags with quick change filter elements and compressed air dischage valves
With a New York pressure blower, driven by a 40HP 3/60/230/460 volt.

Four round cartridge filters
Mounted on legs

exhaust air scrubber,
pressure rated -1/0,5bar @ -10/160 degrees C,
mounted on a carbon steel frame
with a 150 mm diameter stainless steel body scrubber column with carbon steel rushig rings
pressure rated 6bar@ 50 degrees C, with a pump, manufactured by Dickow, type WPVh2561, serial number 03175440
motor type FFD80K4FDS/6612
motor and pump are CE stamped.

• This is a flameless oxidizer, there is no burner and it only accepts a gas flow.

Booster Pump skid
designed to increase water flow , temperature, and pressure for RO system,
and CID system in the following steps of the process.
With one approx. 10 sq ft, ITT Industrial plate heat exchanger
model P7A, with 316 SS SS plates
rated for 150 psi at 302 degrees F on both the process or service side
One, 5 HP, 316 SS centrifugal pump rated for 60 psi
one 5 micron filter in a 316 SS electropolished housing manufactured by Stainless Fluid systems
0.8" OD x 41" high, with 1.5" inlets and outlets
The filter vessel is rated for 150 psi at 300 degrees F.
UV lamp, rated for 254 NM, in a 316 SS polished housing
With digital flow controls, and a US filter power control panel.

vertical cyclone
weld slight coned top,
weld coned bottom
openings top: 1-900mm, straight side: 1-800mm, bottom: 1-250mm,
mounted on 4-lugs

99% UVT for Ozone destruct,
Rated for 120 volts, 60 Hz.
Quartz # QTZ0023, Lamp # LMP12006-V.

Vapors handled: NH3, N2, toluene vapor, 100 #/hr HCL, and 180 #/hr SOC12 vapor
The system uses various recirculation streams depending on the vapors and removes 95-85% of the vapors depending on the conditions.
The system utilizes CS construction for the tank and column, lined with “Flouroshield” Teflon, and also included are a recirculation pump and heat exchanger.
The system design rating is FV/5 psig at 5-200 degrees F.
The pump is a Gould’s size 1 x 1.5 x 8, model 3298, mag drive, and a Tefzel liner,
driven by a 7.5 hp. Ex. Proof motor
The heat exchanger is an APV Model SRS MS-12 with Hastelloy C-276 wetted parts and a surface area of 101.8 Sq.Ft.
The column packing is Hi flow 5/8” rings manufactured from PFA Teflon, With an Otto York mist eliminator
Complete package system base mounted on a CS base 9’ long x 7’ wide.
Top of the column is 106” high.

• Using caustic to scrub acid. Fan was removed, we can replace it. Packed section 4.5 feet, with structured mesh packing. Multiple spray bars at top of tower, 3" feed/spray line, 4"
  return line. 14" gas inlet. Scrubber fan speed 3600 rpm.

130 (@ 94% UVT) GPM
Ultraviolet Water Purifier
One piece compact design including UV treatment and electrical cabinet.
304SS control cabinet
Rated 130 GPM @ 94% disinfection or 156 GPM @ 99% disinfection.
120 psi max. operating pressure. 50°F - 100°F operating temperature.
3" inlets/outlets with optional sanitary fittings. drain and sample port. (Lamps not included).

In Line Sand Media Filter

vertical cyclone,
weld slight coned top,
weld coned bottom,
openings top: 1-900mm, straight side: 1-800mm, bottom: 1-250mm,
mounted on 4-lugs

vertical cyclone,
weld slight coned top,
weld coned bottom
openings top: 1-900mm, straight side: 1-800mm, bottom: 1-250mm,
mounted on 4-lugs

vertical dust collector mounted on legs
with a 30" cone bottom
Contains socks approximately 6" diameter x 70" long
Side access door 40" long x 21" wide. with a 15" diameter Fike rupture disk
Pulsater top is 12" long
Bottom outlet on cone is 6.5" and has a manual slide gate valve
Cone bottom has a 4", 3", and a 2.5" flanged nozzles
Top has a 3" nozzle.
Legs elevate collector 36" off grade.

• Halar coated GRP scrubber system,
• design pressure -0.005Nmm2/+0.35Nmm @ 65 degrees C
• 1700 liter,
• 2.3mm Halar (ECTFE) lining,
• 1800mm liquor depth

The unit is designed to reduce the HCl from a maximum of 1,000 mg/m3 to below 5 mg/m3

at gas flow rates up to 1,250 NM3/hr and with the pH of the scrubbing liquid ranging from

the normal alkaline solution down to a pH of 7.

with (6) 4" diameter x 92" long filtration tubes
Model SS1832B-12400, Serial number 4878325
mechanical seal on shaft