Separation, Filtration & Clarification - Used and Surplus Inventory | IPP

• Side discharge with automatic valve Agitator Cored for Heating/Cooling: Yes. Vessel Liquid Capacity: 400 gallons.

• mobile laboratory filter/dryer with tilting mechanism,
• design pressure internal 1 bar + full vacuum @ -20/150 degrees C, jacket: 6 bar + full vacuum @ -20/150 degrees C,
• all wetted parts are Hastelloy C22,
• 50 liter slurry capacity,
• 20 liter cake capacity,
• 350mm diameter x 680mm straight side,
• 6-30rpm shaft speed,
• agitator driven by 1.5kW, 3/50/230/400 volt, 1420 rpm CE ATEX EExd IIB T4 IP55 motor,
• hydraulic driven agitator raise/lower mechanism with powerpack,
• alloy 22 bellows on shaft,
• flat bottom filter plate with mesh filter and can be rotated for cleaning,
• manual vessel tilt mechanism,
• strip sight glass on side for measuring cake depth,
• approximately 100mm side discharge which is fully contained in a glovebox.
• all mounted on stainless steel frame with wheels for full mobility,
• design code ASME VIII DIV 1 (1998) + A '00'
• Can be used with 248331 APOVAC system for vacuum at an additional cost.

basket only 1/4 " drainage holes Eight 7/8" bolt hole pattern

• Pharmaceutical design. This centrifuge has a clear distinction between the process area/clean room and the drive area. The processing area is free of dead space and allows for complete inspection and sterilization.
• The filter medium is installed inside the cantilever mounted screen basket.
• This centrifuge is Gas tight (over -pressure) to 0.04 bar. With feed and wash pipes, hydraulic plow with pneumatic heel cake removal system and solids discharge chute, with door lock switch.
• Internal accessories are Hastelloy C-22, Gasketing is PTFE.
• Internal appears to have a buff polish.

• Plates are FDA approved and non gasketed.
• Polypropylene plates and frames and all Stainless Steel skeleton.
• Approximately 38 chambers.
• 4 eye closed delivery, 1" inlet and outlets.
• Manual closure with Hydraulic Assist manufactured by SPX. Plate Diameter or Width: 800 mm. Plate Height: 800 mm. Plates Shifted By: Manual.

• Plates are FDA approved- Non Gasketed.
• Polypropylene plates and frames and all Stainless Steel skeleton.
• 44 chambers.4 eye closed delivery,1" inlet and outlet.
• Manual closure with Hydraulic Assist manufactured by SPX. Plate Diameter or Width: 800 mm. Plate Height: 800 mm. Plates Shifted By: Manual.

wall thickness 25 mm belt driven by 45 kw motor, 3/50/380-660 volt, 80mm feed, 300mm discharge on front door, 260mm wide x 660mm long filtrate, central lubrication system, and controls

Alloy C22

Internal finish is a sanitary polish. 304SS sheathing. 304 stainless steel

18.35" Side discharge with discharge valve, 132 gallon Hastelloy C 22 side discharge valve. National Board # 287. rated FV/88 @392 degrees F.

Dryer Dimensions: 90" diameter x 76" length

hydraulic skid. Includes: integral Stock # 241013- Hastelloy C22 pulse jet Dust collector. 8.6" handhole, 4.33" site glass. Agitator Cored for Heating/Cooling: Yes.

• Contour screen bowl centrifuge.
• Reliance 444T frame TEFC motor
• Oil system driven by a Reliance143T TECF, 1 hp 3/60/460 volt motor

• Plates are FDA approved, non Gasketed.
• Polypropylene plates and frames and all Stainless Steel skeleton.
• 95 plates with 44 chambers.
• 4 eye closed delivery, 1" inlet and outlet.
• Manual closure with Hydraulic Assist manufactured by SPX. Plate Diameter or Width: 800 mm. Plate Height: 800 mm. Plates Shifted By: Manual.

Vapors handled: NH3, N2, toluene vapor, 100 #/hr HCL, 180 #/hr SOC12 vapor

peeler centrifuge with a 0.12kw, 3/50/230/400 volt, 1360 rpm fan motor, discharge screw/plow driven by 2.2kw, 3/50/400 volt Ex motor, hydraulic door locking mechanism and cake thickness device driven by a hydraulic pump with a 0.75kw, 3/50/400 volt Ex motor, hinged front door, 1-200mm discharge, 1-250mm filtrate with s/steel tank, centrifuge with (1) Siemens OP37 controller, (1) s/steel GAF filter, (1) diaphragm pump, (1) 600ltr plastic tank, 900mm diameter x 1m high, (1) s/steel centrifugal pump, manufactured by SERO, type SEMA-3111-75-2.32, (1) 35ltr Schott glass reciever, (2) flow meter, (2) pneumatic valves, (1) main control panel

• Single pneumatic hydraulic ram closure mechanism. (completely pneumatic operation, no electric, good for hazardous environments).
• Recessed plate filter press, complete with (25) chambers(1) head plate,5 eye, closed delivery.
• 32mm cake thickness. Plate Height: 18.5 in. Plates Recessed: Yes. Plates Shifted By: Manual.

• Centritec Cell 8 single use insert centrifuge
• This type of flow centrifuge is for harvesting mammalian and insect cells in a single use insert. The system offers these advantages Single use, rapid changeover disposable, Precise servo drive system that minimizes vibration, User friendly, and low maintenance. Cells are pumped peristaltically from the bio reactor to the cell 8, Live cells can be recycled to the reactor, separation occurs in a gamma irritated disposable bladder and tubing system (Separation Insert) The process is three steps separation, isolation, and discharge. An inflatable barrier segregates cell rich material for the superannuant Min/Max Temp=2 -150 degrees C. (this machine has been modified with switches ,plc, and others to control temperature at an exact setpoint) Separation chamber volume 200 ml. Through put 6-120 L/Hr. Width 32.23 ", depth 46.86 ", height 67.99" Weight 640 kg.

• Manual screw closure.
• 4-eye closed delivery. Openings: 4-2". Plate Height: 600 mm. Plate Thickness: 12 mm. Plates Shifted By: Manual.

• Vapors handled: NH3, N2, toluene vapor, 100 #/hr HCL, 180 #/hr SOC12 vapor

with blower and controls With Blower mounted on the side of the filter housing rated. @ -40 to +30°C, single effect, filter resistance 8 mbar with cone bottom for discharge EEX rated Operating Voltage 230/400 Control panel mounted on side. Mounted on 4 legs.
CE-certified.

continous design, rectangular bed with two rectangular decks with 6 x drives type WA 338 - 380 V/8,804 kW/23,6 A/50Hz., 2 vibrating motors mfd by Rhewum, type FX 1000-6, serial # 9212104 and # 9212105

1. siev dia. mesh approx 6mm x 6mm, 2250mm long x 950mm wide, 2. siev dia. mesh approx 2mm x 5mm, 1350mm long x 950mm wide, 1. screen cloth dia. 1000mm wide x 1540mm long, 2. sceen cloth dia. 1000mm wide x 2540mm long, 3. screen cloth dia. 1000mm wide x 2440mm long, material of sieves and screen cloths is 1.4301. Motor data: 220-380 V/4 kW/50 Hz/ 980 rpm by 5370 kg centrifugal force, total weight 2800 kg.

Podbielniak counter current extracting centrifuge job number 106-102 Bowl is 38" OD x 39" Long Hinged 304SS cover CS coated bottom housing Unit has a 2" feed pipe, 3" outlet on bottom housing 230/460 volt motor with VFD controller Drive dimensions are 48" x 40" x 30" high

• Internal Rated 0.7 PSI @ 170 degrees F.
• Electromechanical drive system
• 42" x 12' 6" frame, axial motor, 4080 mm long x 2065 mm wide x 1900 mm high

inlet Carbon Steel skid mounted High Efficiency Fine classifier 3600 RPM rotor max speed.15kW. 460 vac 35 amps Inlet size is 9", outlet is 21" x 19 " square flange. Rejects line is 5" Particle wheel has hinged door for clean out and wheel access This classifier is rated for 2000-2600 m3h, and 200/2400 kG/h Finess is rated for 3.0-4.0 (c/37um).

500 Gallon Manufactured by Alloy Fab for Dartco Shell is .250" thick Top head is .312" thick Cone is .312/.437" thick jacket is .109" thick6.5 turns half pipe on top head18 turns half pipe on straight side5 turns half pipe bottom head All half pipe jacket is 2"

• built to reduce the total NOX to 200mg/m3 of total gas flow as NO2 at fan discharge
• inlet gas flow 138.1 m3/hr
• inlet temperature (10 - 25 degrees C) say design normal = 20 degrees C
• liquor acidification composition 36% CO2 64% N2
• Azide destruction composition 18% NO2 and 82% N2
• Nitrate destruction composition 36% NO2 and 64% N2
• an additional 180m3/hr gas flow into stage 2 tower during purging
• an additional 66m3/hr minimum of oxidation air is added at stage 1 tower inlet
• design code BS4994: 1987 CAT 1
• 10780 liter capacity,
• (2) 1m diameter x 3477m total height Polypropylene lined packed columns, manufactured by Hat International Ltd, design pressure -0.1 barg @ 50 degrees C, bolt flat top, internal spray nozzles, packing is 2 x 1.65m3 of Lanpac 3.5", 2.1m packing height
• (1) Polypropylene lined rectangular holding tank, approx 3.8m long x 1.2m wide x 1.2m high, flat top and bottom,
• (1) 1000 liter Epoxy vinyl Ester resin vertical caustic dosing tank, bolt dished top, weld flat bottom,
• (1) 220/264liter capacity stainless steel dosing pump, manufactured by ProMinent Fluid Control UK Ltd, serial #2007007687, 7 bar pressure, Ex II 2GD IIC T4 x, driven by approx 0.75kW motor,

Water Softner

AB (Sweden) 2 deck vibratory screen size 0.9 x 2.25 (2) vibratory motors, type VV40B/4 (1) motorised rotary lock valve