12" dia x 13'6" long ferrilium/316SS conveyor dryer Rated 5 TPH Shaft 22 rpm Ferrilium housing 316SS hollow screw conveyor outboard bearings 3/60/230/460 volt, Length: 4,115 mm (162 in). Number of Screws: 1. Internal Pressure: 1.03 bar (14.9 psi). Internal Temperature: 148.9 °C (300 °F).
Holoflite dryer Estimated heat transfer area is 78 Sq.Ft. Agitator 16" diameter and 18' long. Material of construction 316SS on the screw and ferrilium vessel outboard bearings Length: 5,486 mm (216 in). Number of Screws: 1. Orientation: Horizontal. Heat Transfer Surface Area: 7.2 m² (78 ft²).
Holoflite dryer Screw 5" pitch Jacket National Board #13718 Total heat transfer area is 128 Sq.Ft Screw has 89 square feet of heat transfer area and jacket has 39 square feet Working volume 13.7 cubic feet. 12" discharge Length: 6,096 mm (240 in). Number of Screws: 1. Jacket Pressure: 2.1 bar (30 psi). Jacket Temperature: 343.3 °C (650 °F). Heat Transfer Surface Area: 11.9 m² (128 ft²).
12" dia x 10' Has 3 1/2" dia rotor, 6" pitch Estimated heat transfer area is 13 sq.ft. Covered hinged trough thru Sterling reducers 160:1 ratio. Packing glands on shaft and outboard bearings. Has 6" dia feed port, 12" x 12" btm end discharge Length: 3,048 mm (120 in). Number of Screws: 1. Jacket Pressure: 0.34 bar (5 psi). Orientation: Horizontal.
thermascrew conveyor Has 3 1/2" dia rotor, 6" pitch Estimated heat transfer area is 13 sq.ft Covered hinged trough motor thru Sterling reducers, 160:1 ratio Packing glands on shaft and outboard bearings Has 6" diameter feed port 12" x 12" bottom end discharge Length: 3,048 mm (120 in). Number of Screws: 1. Jacket Pressure: 0.34 bar (5 psi). Orientation: Horizontal.
Quad screw holo-flight processor Total estimated heating surface area is 1519 sq. ft., Estimated heat transfer surface of material exposed to the trough is 292 Sq. Ft., for the screws is 1227 Sq. Ft. (306.75 sq. ft. each). The processor is fitted with a vapor hood. The trough is 24' long x 98.25" wide x 35" high,(with out hood) 69.3" high (with the hood). Trough volume is 159 cubic foot. Quad screw design with timing gears Width: 2,496 mm (98.3 in). Length: 7,315 mm (288 in). Number of Screws: 4. Internal Pressure: 2.1 bar (30 psi). Internal Temperature: 343.3 °C (650 °F). Jacket Pressure: 2.1 bar (30 psi). Jacket Temperature: 343.3 °C (650 °F). Orientation: Horizontal. Heat Transfer Surface Area: 141.1 m² (1,519 ft²). Product Rate: 5,443 kg/h (12,000 lb/h). Height: 1,760 mm (69.3 in).
type Variocleaner Rated internal pressure 0.005 bar @-10/50 Degrees C carbon steel, heated screws rated 3 bar @ 50 Degrees C, 75 liter each; jacket has two sections 120 liters each bolt flat end 2404mm screw length. Openings: top: 1-650mm, 1-250mm, 4-100mm side glassis, jacket: 3-40mm, bottom: 2-50mm Width: 700 mm (27.6 in). Length: 3,760 mm (148 in). Number of Screws: 2. Internal Pressure: 0.005 bar (0.07 psi). Internal Temperature: 50 °C (122 °F). Jacket Pressure: 6 bar (87 psi). Jacket Temperature: 50 °C (122 °F). Orientation: Horizontal.
Trough rated 80 psi @ 650 F. Double Screw design with 3" Johnson joints on shafts. Trough rated 80 psi @ 650 F. Double Screw design with 3" Johnson joints on shafts. Total heat transfer area is 571 Sq.Ft., screws are 445 Square foot surface area, jacket is 126 Sq.ft. surface area. Heat transfer medium is water. Heat transfer area for screws is rated for 264 gallon fluid volume, 158 gpm flow rate. Contact parts are carbon steel, flight thickness 5/16". Net Trough volume is 74 Cubic foot, rated 60" wc in the trough. Jacket rated for 92 gallons, 39 gpm flow, CS construction. Flat cover on trough. with a DC Drive controller. 20.7 minutes residence time. Originally used as a cooler. Feed rated 15,000 lbs/hr; Bulk density 70; Material Flow 2/4 CFH; Temperature 1560 degrees F, 0 % moisture. Discharge rated 15,000 lbs/hr; Bulk density 70; Material Flow 2/4 CFH; Temperature 550 degrees F, 0 % moisture. 197 gpm water used as heat exchange medium 95 degrees f inlet, 145 degrees discharge. Right hand drive as looking from rotary Joints. Width: 1,676 mm (66 in). Length: 6,096 mm (240 in). Number of Screws: 4. Internal Pressure: 5.5 bar (80 psi). Internal Temperature: 343.3 °C (650 °F). Jacket Pressure: 2.1 bar (30 psi). Jacket Temperature: 343.3 °C (650 °F). Orientation: Horizontal. Heat Transfer Surface Area: 53 m² (571 ft²). Product Rate: 6,804 kg/h (15,000 lb/h). Height: 1,524 mm (60 in).
Dryer or Cooler Trough rated 80 psi @ 650 F. Double Screw design with 3" Johnson joints on shafts. Total heat transfer area is 571 Sq.Ft., screws are 445 Square foot surface area, jacket is 126 Sq.ft. surface area. Heat transfer medium is water. Heat transfer area for screws is rated for 264 gallon fluid volume, 158 gpm flow rate. Contact parts are carbon steel, flight thickness 5/16". Net Trough volume is 74 Cubic foot, rated 60" wc in the trough. Jacket rated for 92 gallons, 39 gpm flow, CS construction. Flat cover on trough. Screws driven by an electric motor through a gear drive. with a DC Drive controller. 3.29 RPM maximum, 20.7 minutes residence time. Originally used as a cooler. Feed rated 15,000 lbs/hr; Bulk density 70; Material Flow 2/4 CFH; Temperature 1560 degrees F, 0 % moisture. Discharge rated 15,000 lbs/hr; Bulk density 70; Material Flow 2/4 CFH; Temperature 550 degrees F, 0 % moisture. 197 gpm water used as heat exchange medium 95 degrees f inlet, 145 degrees discharge. Left hand drive as looking from rotary joint end. Width: 1,676 mm (66 in). Length: 6,096 mm (240 in). Number of Screws: 4. Internal Pressure: 5.5 bar (80 psi). Internal Temperature: 343.3 °C (650 °F). Jacket Pressure: 2.1 bar (30 psi). Jacket Temperature: 343.3 °C (650 °F). Orientation: Horizontal. Heat Transfer Surface Area: 53 m² (571 ft²). Product Rate: 6,804 kg/h (15,000 lb/h).
Holoflight Dryer or Cooler Trough rated 80 psi @ 650 F. Double Screw design with 3" Johnson joints on shafts. Total heat transfer area is 571 Sq.Ft., screws are 445 Square foot surface area, jacket is 126 Sq.ft. surface area. Heat transfer medium is water. Heat transfer area for screws is rated for 264 gallon fluid volume, 158 gpm flow rate. Contact parts are carbon steel, flight thickness 5/16". Net Trough volume is 74 Cubic foot, rated 60" wc in the trough. Jacket rated for 92 gallons, 39 gpm flow, CS construction. Flat cover on trough. Screws driven by an electric motor through a gear drive. with a DC Drive controller. 3.29 RPM maximum, 20.7 minutes residence time. Originally used as a cooler. Feed rated 15,000 lbs/hr; Bulk density 70; Material Flow 2/4 CFH; Temperature 1560 degrees F, 0 % moisture. Discharge rated 15,000 lbs/hr; Bulk density 70; Material Flow 2/4 CFH; Temperature 550 degrees F, 0 % moisture. 197 gpm water used as heat exchange medium 95 degrees f inlet, 145 degrees discharge. Right hand drive as looking from Rotary Joint end. Width: 1,676 mm (66 in). Length: 6,096 mm (240 in). Number of Screws: 4. Internal Pressure: 5.5 bar (80 psi). Internal Temperature: 343.3 °C (650 °F). Jacket Pressure: 2.1 bar (30 psi). Jacket Temperature: 343.3 °C (650 °F). Orientation: Horizontal. Heat Transfer Surface Area: 53 m² (571 ft²). Product Rate: 6,804 kg/h (15,000 lb/h). Height: 1,524 mm (60 in).
Holo-Flite processer Trough rated 80 psi @ 650 F. Double Screw design with 3" Johnson joints on shafts Total heat transfer area is 571 Sq.Ft., screws are 445 Square foot surface area, jacket is 126 Sq.ft. surface area. Heat transfer medium is water. Heat transfer area for screws is rated for 264 gallon fluid volume, 158 gpm flow rate. Contact parts are carbon steel, flight thickness 5/16". Net Trough volume is 74 Cubic foot, rated 60" wc in the trough. Jacket rated for 92 gallons, 39 gpm flow, CS construction. Flat cover on trough. Screws driven by an electric motor through a gear drive. with a DC Drive controller. 3.29 RPM maximum, 20.7 minutes residence time. Originally used as a cooler. Feed rated 15,000 lbs/hr; Bulk density 70; Material Flow 2/4 CFH; Temperature 1560 degrees F, 0 % moisture. Discharge rated 15,000 lbs/hr; Bulk density 70; Material Flow 2/4 CFH; Temperature 550 degrees F, 0 % moisture. 197 gpm water used as heat exchange medium 95 degrees f inlet, 145 degrees discharge. Left hand drive as looking from rotary joint end. Width: 1,676 mm (66 in). Length: 6,096 mm (240 in). Number of Screws: 4. Internal Pressure: 5.5 bar (80 psi). Internal Temperature: 343.3 °C (650 °F). Jacket Pressure: 2.1 bar (30 psi). Jacket Temperature: 343.3 °C (650 °F). Orientation: Horizontal. Heat Transfer Surface Area: 53 m² (571 ft²). Product Rate: 6,804 kg/h (15,000 lb/h). Height: 1,524 mm (60 in).
Quad screw holo-flight processor Total estimated heating surface area is 1519 sq. ft., Estimated heat transfer surface of material exposed to the trough is 292 Sq. Ft., for the screws is 1227 Sq. Ft. (306.75 sq. ft. each). The heating medium is hot oil The processor is fitted with a vapor hood. The trough is 24' long x 98.25" wide x 35" high,(with out hood) 69.3" high (with the hood). Trough volume is 159 cubic foot. Quad screw design with timing gears driven through a SYM Cyclo reducer at a ratio of 231:1. Final screw output is 7.6 to 76 rpm. Width: 2,496 mm (98.3 in). Length: 7,315 mm (288 in). Number of Screws: 4. Internal Pressure: 2.1 bar (30 psi). Internal Temperature: 343.3 °C (650 °F). Jacket Pressure: 2.1 bar (30 psi). Jacket Temperature: 343.3 °C (650 °F). Orientation: Horizontal. Heat Transfer Surface Area: 141.1 m² (1,519 ft²). Product Rate: 5,443 kg/h (12,000 lb/h). Height: 1,760 mm (69.3 in).
Quad screw holo-flight processor. Total estimated heating surface area is 1519 sq. ft., Estimated heat transfer surface of material exposed to the trough is 292 Sq. Ft., for the screws is 1227 Sq. Ft. (306.75 sq. ft. each). The heating medium is hot oil. The processor is fitted with a vapor hood. The trough is 24' long x 98.25" wide x 35" high,(with out hood) 69.3" high (with the hood). Trough volume is 159 cubic foot. Quad screw design with timing gears driven through a SYM Cyclo reducer at a ratio of 231:1. Final screw output is 7.6 to 76 rpm. Width: 2,496 mm (98.3 in). Length: 7,315 mm (288 in). Number of Screws: 4. Internal Pressure: 2.1 bar (30 psi). Internal Temperature: 343.3 °C (650 °F). Jacket Pressure: 2.1 bar (30 psi). Jacket Temperature: 343.3 °C (650 °F). Orientation: Horizontal. Heat Transfer Surface Area: 141.1 m² (1,519 ft²). Product Rate: 5,443 kg/h (12,000 lb/h). Height: 1,760 mm (69.3 in).
Holo-Flight Dryer Total heat transfer area is 204 Sq.Ft., Screw heat transfer area is 148 Sq.Ft., jacket heating surface area is 56 Sq.Ft. Heat transfer medium is steam. rated for 250 psi steam service. 1/4" thick mixing flights with 12 mixing lugs per flight. 3 Ring shaft seals of 316 SS with Garlock food grade packing. Built with bolted ends for easy clean-out. Type A-36 CS jacket on trough with 30 psi working pressure. Two Duff Norton rotary joints for screws. Beier variator , and a Sumitomo gear reducer, all with Falk couplings. Holoflight speed 2.96 RPM (max) and 0.74 rpm (min). Design criteria 2150 lb/hr feed rate, with a 2000 lb/hr discharge rate at 80 lbs/cubic ft., Feed temperature 120 degrees F, discharge temperature 308 degrees F. Width: 304.8 mm (12 in). Length: 5,486 mm (216 in). Number of Screws: 2. Internal Pressure: 2.1 bar (30 psi). Internal Temperature: 343.3 °C (650 °F). Jacket Pressure: 2.1 bar (30 psi). Jacket Temperature: 343.3 °C (650 °F). Orientation: Horizontal. Heat Transfer Surface Area: 19 m² (204 ft²). Product Rate: 907.2 kg/h (2,000 lb/h). Height: 584.2 mm (23 in).