New and Used Equipment

• Pharmaceutical design. This centrifuge has a clear distinction between the process area/clean room and the drive area. The processing area is free of dead space and allows for complete inspection and sterilization.
• The filter medium is installed inside the cantilever mounted screen basket.
• This centrifuge is Gas tight (over -pressure) to 0.04 bar. With feed and wash pipes, hydraulic plow with pneumatic heel cake removal system and solids discharge chute, with door lock switch.
• Internal accessories are Hastelloy C-22, Gasketing is PTFE.
• Internal appears to have a buff polish.

• Internal Rated 0.7 PSI @ 170 degrees F.
• Electromechanical drive system
• 42" x 12' 6" frame, axial motor, 4080 mm long x 2065 mm wide x 1900 mm high

wall thickness 25 mm belt driven by 45 kw motor, 3/50/380-660 volt, 80mm feed, 300mm discharge on front door, 260mm wide x 660mm long filtrate, central lubrication system, and controls

• CS, with rubber lining, Vapor Body, with Alloy support accessories, forced circulation crystallizer, part of a Zero Discharge System (ZLD). The system's major equipment consists of a shell and tube evaporator heater, Vapor body, recirculation pump and centrifuge. Rated for 50 GPM flow10% moisture) and consumes 20 psi steam at 25,00 lbs./hr. Following is a short process description: The feed from Brine Evaporator enters the recirculation piping above the recirculation pump. The feed is mixed with recirculating brine slurry and pumped through the heater where it increases in temperature and is sent to the vapor body. The hot brine flashes down to the saturation pressure inside the vessel, producing vapor and the cycle is repeated. Crystals are formed continuously in crystallizer vapor body and have to be removed. Concentrated product is removed from the system, passed through a centrifuge to remove the solid crystals and is returned to the evaporator recirculation line. The crystals are sent to a landfill. Vapor from the crystallizer is sent to a small barometric condenser using cooling water to condense the vapors. Condensate is mixed with incoming cooling water and is discharged back to the cooling tower. Vent from the condenser is vented by a CS ejector, through a silencer, and out to the atmosphere. Prime condensate from the condensed plant stream is sent back to the primary feed heater to assist in heating incoming Brine Evaporator feed. The following are main components of the system: Stock #228100- crystallizer heater is 5,700 Ft2 of surface area, with 1040 straight tubes, 1.25”OD x 0.028” wall thickness x 12 Feet long, and are constructed of Titanium. The tube sheets are SS316 Ti clad. Heads are made of SS alloy AL6XN & Shell of SS316L. The Crystallizer stock # 228156 is 16’ Dia. x 30’ Overall Height with 60” cone bottom. It is made of rubber lined Carbon steel. (the crystallizer vessel was removed , we have a drawing so a new vapor body can be constructed.) The Crystallizer recirculation pump, stock #228104 is 19,000 GPM with 150 HP motor and fabricated from SS alloy. The centrifuge stock #228101 is Bird Bowl type, 24" diameter x 38" long, rated for 18,304 Lbs./hr. with SS316L contact parts, 30 HP Motor with SS alloy product contact parts.

• Centritec Cell 8 single use insert centrifuge
• This type of flow centrifuge is for harvesting mammalian and insect cells in a single use insert. The system offers these advantages Single use, rapid changeover disposable, Precise servo drive system that minimizes vibration, User friendly, and low maintenance. Cells are pumped peristaltically from the bio reactor to the cell 8, Live cells can be recycled to the reactor, separation occurs in a gamma irritated disposable bladder and tubing system (Separation Insert) The process is three steps separation, isolation, and discharge. An inflatable barrier segregates cell rich material for the superannuant Min/Max Temp=2 -150 degrees C. (this machine has been modified with switches ,plc, and others to control temperature at an exact setpoint) Separation chamber volume 200 ml. Through put 6-120 L/Hr. Width 32.23 ", depth 46.86 ", height 67.99" Weight 640 kg.

basket only 1/4 " drainage holes Eight 7/8" bolt hole pattern

Podbielniak counter current extracting centrifuge job number 106-102 Bowl is 38" OD x 39" Long Hinged 304SS cover CS coated bottom housing Unit has a 2" feed pipe, 3" outlet on bottom housing 230/460 volt motor with VFD controller Drive dimensions are 48" x 40" x 30" high

• Contour screen bowl centrifuge.
• Reliance 444T frame TEFC motor
• Oil system driven by a Reliance143T TECF, 1 hp 3/60/460 volt motor

Podbielniak counter current extracting centrifuge Job # 106-101 Bowl is 38" OD x 39" Long Hinged 304SS cover, CS coated bottom housing Unit has a 2" feed pipe, 3" outlet on bottom housing 230/460 volt motor with VFD controller Drive dimensions are 48" x 40" x 30" high

All wetted parts are 316SS electro polished to 180 grit Designed for 10 to 30 gpm feed rate The unit has EPDM seals and a polypropylene filter cloth The axial drive is 1 HP 3/60/460 volt 1800 rpm.

cake capacity 55 liter centrifugal force: 1250 xg with translation powe rpack, with filtrate discharge tank 875 mm diameter x 700 mm straight side with a 500 mm top opening,, mounted on stand, with control cabinet and stairs

wall thickness 25 mm class B IP 54 with central lubrication system No controls

peeler centrifuge with a 0.12kw, 3/50/230/400 volt, 1360 rpm fan motor, discharge screw/plow driven by 2.2kw, 3/50/400 volt Ex motor, hydraulic door locking mechanism and cake thickness device driven by a hydraulic pump with a 0.75kw, 3/50/400 volt Ex motor, hinged front door, 1-200mm discharge, 1-250mm filtrate with s/steel tank, centrifuge with (1) Siemens OP37 controller, (1) s/steel GAF filter, (1) diaphragm pump, (1) 600ltr plastic tank, 900mm diameter x 1m high, (1) s/steel centrifugal pump, manufactured by SERO, type SEMA-3111-75-2.32, (1) 35ltr Schott glass reciever, (2) flow meter, (2) pneumatic valves, (1) main control panel

• 300 GPM, Zero Discharge System brine evaporator/crystallizer system (ZLD)System includes a falling film evaporation system, with mechanical vapor recompression, and a forced circulation crystallizer.
• Previously used by a major utility company. This process has been maintained to an excellent standard. The overall system is designed to concentrate 300 GPM flow rate Reverse Osmosis reject stream to essentially dry, land fillable solids. Distillate produced in the evaporator / crystallizer is of high quality ( less than 10 mg/l TDS excluding volatiles) and suitable to recycle.There are two 150 GPM, MVR falling film Brine Evaporators followed by a 50 GPM feed flow rate, steam driven, forced circulation type Brine evaporative crystallizer. A centrifuge is integrated with the crystallizer to produce solids suitable for a landfill.
• All major and minor components are included including some but not all field instrumentation. The evaporator uses "seeding" crystals in the slurry in order to prevent scale up on the tubes. Major items are as follows: Two (2) 150 GPM falling film evaporators with titanium tubes, and flood box/sump constructed of AL6XN and 316 SS. Each evaporator has a MVR system with a mechanical compressor provided by Dresser-Rand, and a recirculation pump by ITT rated for 5000 gpm. ( IPP stock numbers 228146 & 228148) ; One 50 GPM crystallizer, previously had a rubber lined vessel, but was removed due to bad rubber. (vessel can be re fabricated from either SS or CS). Also with a 3,500 sq.ft. shell and tube heat exchanger, and a recirculation pump rated for 19,000 GPM. The heater has wetted parts of AL6XN, and the pump alloy is CD4MCu. ( IPP stock numbers 228100 through 228110) Dry product is discharged through a Bird centrifuge rated for 18,000 lbs./hr. (IPP stock number 228101)

top load, bottom discharge, 12mm thick basket, 3.15 square meter filter area, 1100 rpm permissible speed single motion plow driven by a hydraulic powerpack, powerpack driven by approx 0.75kw EX motor, mounted on a steel baseplate,

spare top and bottom section bottom discharge basket centrifuge bottom discharge design

• 316L stainless steel hinged front cover,
• cake discharge via a pivoting peeling device equipped with a broad peeler knife,
• cake level gauge,
• centrifuge on anti-vibration rubber mountings

• Halar lined basket

clarifier basket centrifuge bottom discharge (2) horizontal baffles basket capacity 7.6 cu ft. 316SS basket, curb and plow Top driven by hydraulic powerpak Hinged access port 1" rotary pneumatic skimmer

single lead conveyor w/hardfacing Used on Dorr Oliver 16L and Flottweg Z3L

2-chamber bowl clarifier centrifuge. Complete with bowl, parts and tools in separate crate.

with single action pneumatic operated plow cylinder.(no Plow) Cover has an inspection door with a 9" sight glass Cover has the following openings for piping connections One, 6" weld neck flange, One 2" opening for feed pipe, Three, 1" opening for accessories.

• CE Ex II 2 Gc T4 classification,
• top load bottom discharge,
• perforated basket,
• basket aperture 1120mm,
• centrifugal acceleration 503g,
• basket underdriven by 37/43kw, 3/50-60/690-400/660-380/415-440 volt 987/985/988/1184 rpm EEx de IIC T4 IP55 ATEX motor,
• full opening clamp dished top with hydraulic assist,
• hydraulic driven plow,
• both driven by the same power pack,
• power pack driven by 2.2kw, 3/50/400 volt 1500 rpm EEx de IICT4 IP55 motor, motorised filling disc driven by 5.5/6.3kw, 3/50-60/690-400/660-380/415-440 volt, 1448/1439/1452/1740rpm EEx de IIC T4 IP55 ATEX motor,
• centrifuge used with nitrogen,
• 200mm liquid outlet,
• mounted on a 316L stainless steel frame with rubber mountings,

Frame SN 1647477, bowl SN 1641173 Has tools, controls and manuals.

• nozzle type disk bowl centrifuge,
• 5440 rpm,
• 1.03 kg/dm3 heavy liquid,
• 1.07 kg/dm3 solid,
• hinged top cover,
• driven by 45kW, 3/50/380 volt 1470 rpm IP55 motor,