Stainless Steel 304 Niro SD-25 N-R Dryer-Spray - IPP# 207374

Type: Dryer-Spray

Manufacturer: Niro

Model: SD-25 N-R

Condition: Used

Material: Stainless Steel 304

Diameter: 3,400 mm (133.9 in)

Atomizer Type: Inline Mixing Nozzle

multifunctional spray dryer system, with nozzle type atomization, and baghouse filter. on Zinc Oxide, but can dry other inorganic compounds. This spray dryer is an all welded unit comprised of a chamber and cone with the following dimensions: 3.4m diameter x 4.8m straight side x 2.3m coned bottom, 700mm x 400mm access door, chamber with pneumatic hammers for helping powder discharge, Drying gas is supplied by a Niro direct gas fired air heater with Maxon airflow burner type NP-35.5, fabrication # 472, liquid petroleum gas fired, 334 kw nominal load, gas supply pressure 8mbar (min), 21 mbar (max). Product/ drying gases are separated by a bag filter: a 31 square meter (339 square feet) The system also includes the following optional accessories. (1) s/steel centrifugal spray pump, manufactured by Pasilac, type K2-3805-185, serial # 137868, driven by an electric motor. (1) 1700 liter 304 s/steel feed tank with clamp on agitator, open top, weld coned bottom, 1.5m diameter x 1000mm straight side, air driven agitator, tank mounted on (4) carbon steel legs. (1)600mm diameter s/steel single deck vibratory sieve, type VSC600-1-SS, manufactured by Vibrodynamics, serial # 664P driven by 0.5 kw, 3/50/380/420 volt, 1440 rpm motor. (1) s/steel 3110 m3/hr @ 160 deg C fan, manufactured by B.Bille, type HT35-530, fan speed 2790 rpm, 11 kw, 2930 rpm motor. (1) Feluwa high pressure feed pump, type SGL-232/3-K50-M190-ZW, serial # 21/26322, 0.47 m3/hr., 1.5 kw, 1400 rpm.

Evaporation Rate: 210 kg/h (463 lb/h). Inlet Temperature: 425 °C (797 °F). Outlet Temperature: 130 °C (266 °F). Heating Type: Gas.

Type: Dryer-Spray

Manufacturer: Niro

Model: Utility Unit

Condition: Used

Material: Stainless Steel 304

Diameter: 1,219 mm (48 in)

Atomizer Type: Single Fluid Pressure Nozzle

Utility Model pilot size used for scale up work Rated for 20 lbs.hr with atomizing nozzle with conical bottom.

Evaporation Rate: 9.1 kg/h (20 lb/h). Heating Type: Gas. Height: 1,829 mm (72 in).

Type: Dryer-Spray

Manufacturer: Niro

Condition: Used

Material: Stainless Steel 304

Diameter: 7,000 mm (275.6 in)

Evaporation Rate: 1,800 kg/h (3,968 lb/h)

nozzle type spray dryer system with integrated fluid bed, directly heated with heat recovering, 45% DS feed, product is a micro Granulate, spray nozzle feed (unavailable)dryer directly heated by gas burner, bottom of the dryer has an integrated fluid bed with rotary lock valve,(1) 3.2 m3/hour stainless steel Feluwa feed pump, pressure 120 bar, (2) 21,000 liter stainless steel cyclones, manufactured by Niro, pressure 1 bar @ 120 degrees C, each with a rotary lock valve, (1) Stainless steel pre-cyclone, manufactured by Niro, pressure 1.01 bar @ 120 degrees C, with 2-rotary lock valves, (1) 54000 Nm3/hour stainless steel main blower/fan, manufactured by Niro, fabrik #F388334/1, pressure 1.03 bar @ 120 degrees C, driven by 170 kW, 1490 rpm motor,2) 0.8 m3/hr. twin screw coolers, manufactured by Engelmann, driven by 3kw motor, stainless steel fresh air blower, manufactured by Niro, driven by 7.5kw motor with air filter, (1) 13 square meter stainless steel heat exchanger, manufactured by Niro, pressure 1.04 bar @ 800/250 degrees C, (2) 105,000 liter Aluminum silos, manufactured by Buhler, 3m diameter, pressure 1.03 bar @ 20 degrees C, each with a dust filter mounted on top, (1) stainless steel wet scrubber system which includes (1) 50,000 liter stainless steel vertical Scrubber, pressure 1.03 bar @ 120/40 degrees C, 2.8m diameter, 90kw motor, (2) 78.2 square meter stainless steel plate heat exchangers, manufactured by GEA, pressure 3 bar @ 40/20 degrees C, (2) 265 m3/hour stainless steel centrifugal pumps, driven by 17.5kw motor, (1) 1500 liter vertical separator tank, manufactured by Niro, 2m diameter, pressure 1.03 bar @ 40 degrees C, and other ancillaries ,other ancillaries, dryer system also includes other minor ancillaries such as valves, flow meters etc.

Inlet Temperature: 280 °C (536 °F). Air Flow Rate: 54,000 m3/h (31,783 CFM). Pressure: 1.3 bar (18.9 psi). CIP: Yes. Heating Type: Gas. Height: 18,000 mm (708.7 in).

Type: Dryer-Spray

Manufacturer: Niro

Condition: Used

Material: Stainless Steel 304

Diameter: 5,664 mm (223 in)

Atomizer Type: Rotary Disc-Wheel

18' 7" diameter x 31' long with cone bottom Discharge through an 8" rotary valve onto a vibrating conveyor, 9" wide x 3" high by 24' long, that uses air to cool the product. Hot air is gas fired, with a newer Honeywell flame control system on the burner. Three 36" dust collecting cyclones, discharge to product conveyor. One Niro atomizer Model F35/4EAIC, # 516. Top mount oilers and controls for atomizers. Atomizers are belt driven by a reliance DC drive with a variable speed controller. Analog control panel with relay logic. The following items are with the complete package: 18' Niro dryer, including the gas fired burner. One F-35 Atomizer, One Air compressor, One Reliance electric drive for atomizer, one exhaust fan, three cyclone dust collectors, One vibrating conveyor system , One Vibrating screen, Electric controls and Instruments, two jacketed mixing tanks, One Churn, one colloid mill, one Westfalia centrifuge, two stainless steel feed tanks, Associated piping and ductwork as it applies to the machine.

Evaporation Rate: 362.9 kg/h (800 lb/h). Heating Type: Gas. Height: 9,449 mm (372 in).