with ribbon mixer 316SS wetted parts Vessel rated for FV/15 psi at 307 degrees F with drive end head welded, opposite drive end bolted for removal. The dryer is supported by heavy duty channel legs. The vessel internal finish 180 grit polish in the product contact areas. Vessel nozzle schedule is as follows: One 20” top opening, One 12” bottom opening, Two 10” top openings, One 6” top for pressure relief, three 6” top sight glass assembly’s, Four 3” spares, one 2” N2 connection. Two 2” nipples on the heads for cleaning and two ¾” nipples for Thermowells. Spare Rotor available for additional cost. Capacity Design: 17 m3 (600 ft3). Capacity Working: 12.3 m3 (434 ft3). Diameter: 1,829 mm (72 in). Length: 4,877 mm (192 in). Height: 3,048 mm (120 in). Temperature: 152.8 °C (307 °F). Pressure: 1.03 bar (15 psi). Orientation: Horizontal. Agitation: Yes. Jacket Material: Carbon Steel. Jacket Pressure: 4.1 bar (60 psi). Jacket Temperature: 152.8 °C (307 °F).
Drais Mannheim plow type Rotary Vacuum Dryer system with a dust collector Plow blades on mixing shaft and choppers mounted in side wall Unit has Carbon steel internals With an (6) choppers/homogenizers, each 7,5 Kw, 1500 rpm 3/50/230/400 volt Dryer includes: 42 square meter S316SS tube & Head, carbon steel shell horizontal vacuum condenser manufactured by Shin Meiwa Industry, Kobe Japan rated ).5 Bar @ 90 degrees C in the shell, 6 bar @ 42 degrees C in the tubes. A top mounted dust collector, a vacuum pump and control panel. Vertical dust collector has eight filters, each is 150mm diameter x 1500 mm long, estimate filter area at 46 m2 (504 sq.ft.). Capacity Design: 16 m3 (565 ft3). Capacity Working: 12 m3 (423.8 ft3). Diameter: 2,060 mm (81.1 in). Length: 4,800 mm (189 in). Temperature: 110 °C (230 °F). Pressure: 1 bar (14.5 psi). Agitation Seal Type: Mechanical. Number of Choppers: 6. Jacket Material: Carbon Steel. Jacket Pressure: 3 bar (43.5 psi). Jacket Temperature: 140 °C (284 °F).
Designed for batch operation. Designed for vacuum operation to -25 "hg. Internal finish polished to a 120 grit finish. Main shaft drive 10 Hp with gear reducer for output rpm of 65. Center bottom discharge 15.5" ID. No dust collector with unit. Capacity Design: 0.62 m3 (22 ft3). Capacity Working: 0.37 m3 (13 ft3). Diameter: 939.8 mm (37 in). Length: 2,540 mm (100 in). Height: 4,064 mm (160 in). Temperature: 121.1 °C (250 °F). Pressure: 1.03 bar (14.9 psi). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Operational Mode: Batch. Number of Choppers: 2. Jacket Pressure: 5.2 bar (75 psi). Jacket Temperature: 160 °C (320 °F).
Rotary vacuum dryer CRN # H 9634.5 shell thickness .500,material SA 240/304 head thickness 1.00, head material SA 516-70 Sigle ribbon carbon steel mixer Driven by a Baldor AC motor through a gearbox 230/460 v, UL listed class 1 group D Drum measures 120" long x 51" w x 51" h. Capacity Design: 4 m3 (140 ft3). Capacity Working: 2.8 m3 (100 ft3). Diameter: 1,295 mm (51 in). Length: 3,048 mm (120 in). Height: 1,295 mm (51 in). Temperature: 121.1 °C (250 °F). Pressure: 1.72 bar (25 psi). Orientation: Horizontal. Operational Mode: Batch. Agitation: Yes. Agitation Seal Type: Packing. Jacket Pressure: 4.1 bar (60 psi). Jacket Temperature: 121.1 °C (250 °F).
Jacketed rotary vacuum batch paddle dryer with static chopper blades Patent and designed by List DTB manufacturing #3000.01.01.01.3000, working pressure internal -1/6 bar @ 260 degrees C (11000 liter), jacket 6 bar @ 260 degrees C (511 liter), shaft 6 bar @ 260 degrees C (560 liter), bolt flat ends, 316Ti stainless steel (1.4571) half pipe coil jacket on straight side and both ends, paddle driven by a 110/112w, 3 phase, 50/60 Hz, 400-690/460 volt, 1488/1791 rpm, IP 55 siemens CE motor via a Flender 906/9.4 rpm reduction gearbox paddle speed 9.4 rpm openings top: 1-800mm (filter), 4-250mm, 4-150mm (product inlet), 2-150mm, 2-50mm, 4-50mm (jacket), side: 8-50mm (jacket), bottom: 1-150mm (center discharge), 1-80mm, 4-50mm, both flat ends: 2-50mm (jacket) dryer with dust filter, cyclone Capacity Design: 10 m3 (353.1 ft3). Capacity Working: 6.7 m3 (236.6 ft3). Diameter: 1,900 mm (74.8 in). Length: 4,930 mm (194.1 in). Temperature: 260 °C (500 °F). Pressure: 6 bar (87 psi). Orientation: Horizontal. Operational Mode: Batch. Agitation: Yes. Agitation Seal Type: Packing. Dust Collection: Yes. Jacket Material: Stainless Steel Austentic. Jacket Pressure: 6 bar (87 psi). Jacket Temperature: 260 °C (500 °F). Jacket Type: Half Pipe/Limpet.
jacketed turbo dryer system with water content of dry product @ 0.5% and a dry particle size of >420 microns, capacity, gas fired, steam drum type, 500 rpm turbine speed operating pressure of drum is slightly below atmospheric @ 180/100 degrees C jacket 10 bar g @ 175 degrees C, design pressure of jacket 12 bar g @ 220 degrees C, heater type air jet burner, 500000 kCal, operating temperature 200 degrees C, design pressure 400 degrees C, 1.3m outside diameter x 6060mm long drying chamber, internal blades to keep product on the sidewall and to push product down the dryer, internal self cleaning in done via reverse rotation of the drum Capacity Design: 10 m3 (353.1 ft3). Capacity Working: 6.6 m3 (233.1 ft3). Diameter: 1,300 mm (51.2 in). Length: 6,060 mm (238.6 in). Temperature: 400 °C (752 °F). Heat Transfer Surface Area: 28.5 m² (306.8 ft²). Jacket Pressure: 12 bar (174 psi). Jacket Temperature: 220 °C (428 °F).
cylindrical design Vessel designed for 14.9 psi and full vacuum rated at 29.92” Hg. This machine is designed for continues operation but was previously used in a batch process. The jacket is two zone style with 3” half pipe. The manufacturer indicated this machine is designed for sanitary applications. The agitator shaft is not cored for heating, 6” diameter 304 SS, with 12, ¾” thick posts and paddles. Paddles are 12” long x 6.5” wide. Agitator clearance is 1/8” nominal at the lowest point. Rotation of the agitator is counter clockwise at 25 rpm. Agitator is driven by a right angle geardrive manufactured by SEW Eurodrive with a 40 Hp AC motor. Model # KAF157DV200L4. The geardrive has a 70.38:1 ratio rotating the output shaft at 25 rpm. The agitator is sealed by two Woodex, fully spit Meco mechanical seals, and rides on two Dodge expansion type flange bearings. Top connections are one 24” flanged nozzle for vacuum filter, one 24” manway, and one 16” loading flange. Discharge nozzle is 8” flanged. Shell is wrapped with 14 Gauge 304 SS, covering 2” thick Ceramawol insulation designed to limit the dryers exterior temperature to <140 degrees F. The baghouse filter is 304 SS, and is 32” in diameter x 62” high. The bottom of the dust collector bolts directly to the dryer by a flange, and the top has a bolted 28” diameter man way for filter changes. Capacity Design: 2.8 m3 (100 ft3). Capacity Working: 1.7 m3 (60 ft3). Diameter: 1,118 mm (44 in). Length: 3,048 mm (120 in). Height: 2,134 mm (84 in). Pressure: 1.03 bar (14.9 psi). Orientation: Horizontal. Operational Mode: Continuous. Agitation: Yes. Agitation Seal Type: Mechanical. Jacket Material: Stainless Steel 304. Jacket Pressure: 8.6 bar (125 psi). Jacket Temperature: 218.3 °C (425 °F). Jacket Type: Half Pipe/Limpet.
Cored shaft, jacket chamber. No motor available. Motor Power: 55.9 kW (75 HP). Diameter: 203.2 mm (8 in). Length: 3,048 mm (120 in). Orientation: Horizontal. Pressure: 6.9 bar (100 psi). Temperature: 343.3 °C (650 °F). Jacketed: Yes.
rotary vac dryer Single ribbon design w/spring loaded scraper blades Removable agit and hollow shaft Has outboard bearing and mech seals Openings: top 3-12" (2 have pneumatically operated slide gate valves), 1-10", 2-2"; btm 1-10" w/manual valve 3/60/230/460 volt UL label Capacity Design: 1.98 m3 (70 ft3). Capacity Working: 1.5 m3 (53 ft3). Diameter: 914.4 mm (36 in). Length: 4,572 mm (180 in). Temperature: 148.9 °C (300 °F). Agitation: Yes. Jacket Material: Carbon Steel. Jacket Pressure: 3.4 bar (50 psi). Jacket Temperature: 148.9 °C (300 °F).
NS# P-76551-1 Rated FV internal @ 300 degrees F Shell is 5' ID X 20' long Capacity Design: 9.4 m3 (333 ft3). Capacity Working: 7.1 m3 (250 ft3). Diameter: 1,524 mm (60 in). Length: 6,096 mm (240 in). Height: 2,134 mm (84 in). Temperature: 148.9 °C (300 °F). Orientation: Horizontal. Agitation: Yes. Jacket Material: Carbon Steel. Jacket Pressure: 3.4 bar (50 psi). Jacket Temperature: 148.9 °C (300 °F).
304SS shell with CS jacket Openings: top 1-14", 1-12", 1-24" w/28" dia x 36" str side air receiver Center btm discharge 1-12" Rotor speed 6 rpm Capacity Design: 4 m3 (141 ft3). Capacity Working: 1.98 m3 (70 ft3). Diameter: 1,219 mm (48 in). Length: 3,962 mm (156 in). Pressure: 2 bar (29 psi). Shaft Cored and National Board Stamped: Yes. Agitation: Yes. Agitation Seal Type: Packing. Jacket Material: Carbon Steel. Jacket Pressure: 8.1 bar (118 psi).
Rotary Vacuum Paddle Dryer with heated shaft. Vessel rated for Full vacuum internal 316SS internals, SS 1/2 pipe coil jacket. one head bolted dished, one head welded dished. Unit has approx. 12" diameter heated shaft with paddle agitator blades. Shaft is direct coupled to a gear reducer motor3/60/230/460 volt Openings inlcude: (1) 18" Top, (1) 12" x 16" end port with hinged cover, Bottom center discharge. Capacity Design: 2.8 m3 (100 ft3). Capacity Working: 2.5 m3 (90 ft3). Diameter: 1,219 mm (48 in). Length: 3,658 mm (144 in). Height: 1,422 mm (56 in). Orientation: Horizontal. Jacket Material: Stainless Steel Other. Jacket Pressure: 4.1 bar (60 psi). Jacket Type: Half Pipe/Limpet.
Rotary Vacuum Paddle Dryer with heated shaft. Vessel rated for Full vacuum internal 316SS internals SS 1/2 pipe coil jacket one head bolted dished, one head welded dished. Unit has approx. 12" diameter heated shaft with paddle agitator blades. Shaft is direct coupled to a gear reducer 3/60/230/460 volt Openings include: (1) 18" Top, (1) 12" x 16" end port with hinged cover, Bottom center discharge. Capacity Design: 2.5 m3 (90 ft3). Capacity Working: 1.7 m3 (60 ft3). Diameter: 1,219 mm (48 in). Length: 3,658 mm (144 in). Height: 1,422 mm (56 in). Orientation: Horizontal. Agitation Seal Type: Packing. Jacket Material: Stainless Steel Other. Jacket Pressure: 4.1 bar (60 psi). Jacket Type: Half Pipe/Limpet.
Rotary vacuum dryer Vessel rated for Full vacuum 12.5" diameter cored shaft with 24 fixed plows. Outboard bearings with packing glands. Capacity Design: 2.8 m3 (100 ft3). Capacity Working: 1.98 m3 (70 ft3). Diameter: 1,219 mm (48 in). Length: 3,048 mm (120 in). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Agitation Seal Type: Packing. Jacket Pressure: 2.4 bar (35 psi). Jacket Temperature: 104.4 °C (220 °F).
4' diameter x 10' long chamber. as 24" cored shaft with paddles and removable scrapers. No drive available. Unit has chain guards for drive. Top openings one 12", one 10 ". Jacket openings are 2" NPT. 12" bottom discharge. Capacity Design: 3.5 m3 (125 ft3). Capacity Working: 2.3 m3 (82 ft3). Diameter: 1,219 mm (48 in). Length: 3,048 mm (120 in). Height: 2,134 mm (84 in). Agitation Seal Type: Packing. Jacket Material: Carbon Steel.
jacketed rotary vacuum paddle dryer Internal design pressure: -1/6 bar @ -10/150 degrees C (10180 liter) Coil jacket: 6 bar @ -10/150 degrees C (500 liter) Rotor/paddle: 6 bar @ -10/150 degrees C (300 liter) (1) bolt flat end (drive), (1) clamped flat end, rotor/paddle with union joint and cored for steam heating, rotor/paddle driven by approx 100kw motor via a gearbox center bottom discharge Capacity Design: 10 m3 (353.1 ft3). Capacity Working: 6.7 m3 (236.6 ft3). Diameter: 1,800 mm (70.9 in). Length: 4,075 mm (160.4 in). Temperature: 150 °C (302 °F). Pressure: 6 bar (87 psi). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Operational Mode: Batch. Jacket Material: Stainless Steel 321. Jacket Pressure: 6 bar (87 psi). Jacket Temperature: 150 °C (302 °F). Jacket Type: Half Pipe/Limpet.
Internals polished---Shaft Not cored. Packing on shaft, No dust collectors. Capacity Design: 2.1 m3 (75 ft3). Capacity Working: 1.27 m3 (45 ft3). Diameter: 1,118 mm (44 in). Length: 1,981 mm (78 in). Heat Transfer Surface Area: 7 m² (75 ft²). Orientation: Horizontal. Operational Mode: Batch. Agitation: Yes. Agitation Seal Type: Packing. Jacket Material: Stainless Steel 304. Jacket Pressure: 8.6 bar (125 psi). Jacket Temperature: 176.7 °C (350 °F). Jacket Type: Dimple.
vertical vacuum dryer system Shell 1800 mm diameter x 900 mm straight side x 1400 mm conical section. With vertical rotating screw. Vibratory hammers on the conical section. Openings on dryer/mixer: Top 500 mm manway with cover, 1-200 mm. With vertical stainless steel condenser/ preheater, 300 mm diameter x 1600 mm long, single pass design. Under the filter is a stainless steel rotary airlock driven by 0.37kW 3/50/220/380V 1390 RPM motor. With Werner & Pfleiderer type DRT 250/6, serial number 163305, 1.4571 dryer rated 4700 KJ/Hour. Spiral rated 6 bar, jacket rated 6 bar @ 200 degrees C. Spiral driven by 0.37 kW, 3/50/380V motor. Mixer/ dryer discharges into a rotary airlock type GAC 187, with 200 mm feed and 100 mm discharge openings. With variable speed drive. Bottom of mixer has a pneumatic operated valve. From airlock product is fed into a 1.4571 rotating screen manufactured by Gericke, 200 mm diameter x 750 mm long, driven by 2.2 kW 3/50/220/380V 450 RPM motor. system includes a screw conveyor to the filler, manufactured by Independent Scale, serial number 18273, rated 25 KG @ 1250 RPM. Capacity Design: 3 m3 (105.9 ft3). Capacity Working: 2 m3 (70.6 ft3). Diameter: 1,800 mm (70.9 in). Length: 2,300 mm (90.6 in). Orientation: Vertical. Agitation: Yes. Agitation Seal Type: Packing. Dust Collection: Yes. Jacket Pressure: 6 bar (87 psi). Jacket Temperature: 200 °C (392 °F).
Shell rated full vac @ 300 deg F Has 24" dia removable cored rotor w/SS paddles and teflon scrapers Openings: top 2-24"; btm 1-24" No drive grearbox or rotary joint Capacity Design: 7.9 m3 (280 ft3). Capacity Working: 5.4 m3 (190 ft3). Diameter: 1,219 mm (48 in). Length: 9,144 mm (360 in). Temperature: 148.9 °C (300 °F). Jacket Material: Carbon Steel. Jacket Pressure: 3.4 bar (50 psi). Jacket Temperature: 148.9 °C (300 °F).
25 Liter Double Shaft Kneader Mixer with 1.4306 s/steel Double wall jacket internal -1/+0,5 bar hydraulic drive Motor Power: 10 kW (13.4 HP). Capacity (Design): 30.6 L (8.1 gallons). Length: 944 mm (37.2 in). Orientation: Horizontal. Pressure: 0.5 bar (7.3 psi). Temperature: 350 °C (662 °F). Jacket Pressure: 6 bar (87 psi). Jacket Temperature: 350 °C (662 °F). Jacket Material: Stainless Steel 304L.
product contact Designed for batch operation. Designed for vacuum operation to -25 "hg. Internal finish polished to a 120 grit finish. Center bottom discharge 15.5" ID. Capacity Design: 0.62 m3 (22 ft3). Capacity Working: 0.37 m3 (13 ft3). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Operational Mode: Batch. Agitation Seal Type: Packing. Number of Choppers: 2. Jacket Pressure: 5.2 bar (75 psi). Jacket Temperature: 160 °C (320 °F).
rotary vacuum dryer Shell 24" (600mm) diameter x 40" (1000mm) long with rotary joint Flat bolted heads Openings: 1-200mm handhole with hinged cover, 1-150mm, 1-100mm; 1-175mm bottom outlet; jacket 4-25mm Capacity Design: 0.25 m3 (8.8 ft3). Capacity Working: 0.18 m3 (6.4 ft3). Diameter: 600 mm (23.6 in). Length: 1,000 mm (39.4 in). Pressure: 3 bar (43.5 psi). Shaft Cored and National Board Stamped: Yes. Agitation Seal Type: Packing. Jacket Pressure: 32 bar (464.1 psi).
vessel pressure full vacuum estimated design temp 120/130 degrees C (2) top doors with hydraulic lifts Ribbon type blades Driven by 14/21 KW, 3/50/500 volt, 980/1470 rpm motor with XP push buttons Capacity Design: 1 m3 (35.3 ft3). Capacity Working: 0.66 m3 (23.3 ft3). Temperature: 130 °C (266 °F). Orientation: Inclined. Jacket Material: Carbon Steel. Jacket Pressure: 6 bar (87 psi). Jacket Temperature: 130 °C (266 °F). Jacket Type: Half Pipe/Limpet.
Vacuum dryer system internal pressure rated -1/+1bar @ -10/+165 degrees C (volume 250 liter), jacket pressure rated -1/+8bar @ -10/+165 degrees C (volume 35 liter) type CD180M-4 3~/50Hz/230-400V/1,460rpm CE confirm, EExdeIICT4, system including: (1) 3.1m² 1.4571 stainless steel tube and shell heat exchanger/condenser, (1) 8m³/h @ 3m head iron cast centrifugal pump, (1) 50 liter 1.4571 stainless steel condensate receiver, (1) 20 liter 1.4571 stainless steel gas separator, (1) 17.5 liter 1.4571 stainless steel jacketed pressure tank, (1) Frequency converter on pallet, (2) stainless steel guards on pallet, (2) Valves and (1) chain on pallet, Accessories on pallet Capacity Design: 0.25 m3 (8.8 ft3). Capacity Working: 0.17 m3 (6 ft3). Diameter: 600 mm (23.6 in). Length: 2,300 mm (90.6 in). Height: 2,195 mm (86.4 in). Temperature: 165 °C (329 °F). Pressure: 1 bar (14.5 psi). Agitation Seal Type: Mechanical. Jacket Material: Stainless Steel Austentic. Jacket Pressure: 8 bar (116 psi). Jacket Temperature: 165 °C (329 °F).
jacketed vacuum Paddle Dryer with carbon steel jacket internal pressure -1/0.5bar @ 130 degrees C (8.300liter) jacket pressure 6 bar @ 200 degree C (280 liter) shaft cored for steam 18.5kW/3~/50Hz/230-400V/465rpm Motor Capacity Design: 8.3 m3 (293.1 ft3). Capacity Working: 7.5 m3 (264.9 ft3). Diameter: 1,895 mm (74.6 in). Length: 3,500 mm (137.8 in). Height: 2,530 mm (99.6 in). Temperature: 130 °C (266 °F). Pressure: 0.5 bar (7.3 psi). Shaft Cored and National Board Stamped: Yes. Jacket Material: Carbon Steel. Jacket Pressure: 6 bar (87 psi). Jacket Temperature: 200 °C (392 °F).
jacketed rotary vacuum paddle dryer TUV certified design pressure vessel -1/1 bar @ -20/200 degrees C (3193 liter), jacket 6 bar @ -20/200 degrees C (151.5 liter), paddle 6 bar @ -20/200 degrees C (208 liter) a rotary union joint driven by 15/17.30kw, 3 phase, 50/60 Hz, 380-415/660-720/440-480 volt, 1465/760 rpm IP55 motor 321 stainless steel dimple jackets on the ends Capacity Design: 3 m3 (105.9 ft3). Capacity Working: 2 m3 (70.6 ft3). Diameter: 1,000 mm (39.4 in). Length: 3,000 mm (118.1 in). Temperature: 200 °C (392 °F). Pressure: 1 bar (14.5 psi). Jacket Material: Stainless Steel 321. Jacket Pressure: 6 bar (87 psi). Jacket Temperature: 200 °C (392 °F). Jacket Type: Half Pipe/Limpet.
Rotary Vacuum Dryer Contract # UD-24819 vacuum test pressure is 850 mbar jacket 3 bar, test pressure is 13 barg Approximately 3800 liter, weld dished heads 316 stainless steel internal ribbon Staffa model B270/P-TACHO hydraulic motor via a hydraulic power pack. power pack driven by a Rexroth pump, type IPV2V4-18/50RA01-MN160A1, Exd 11B T4 Openings include a center bottom discharge design code BS-5500 CAT 2 Capacity Design: 3 m3 (105.9 ft3). Capacity Working: 2 m3 (70.6 ft3). Diameter: 1,500 mm (59.1 in). Length: 5,100 mm (200.8 in). Height: 2,450 mm (96.5 in). Pressure: 8 bar (116 psi). Heat Transfer Surface Area: 9.3 m² (100 ft²). Orientation: Horizontal. Agitation: Yes. Jacket Material: Stainless Steel 316. Jacket Pressure: 3 bar (43.5 psi).
vac dryer (cooler). 316SS shell Total capacity 0.72 cbm Shell 600mm (24") dia x 3.8m (12'6") long Has 18" dia removable cored rotor. Has 9" long scraper blades on shaft. Has (17) fixed delumpers on str side of vessel. Openings: top 2-24" w/bolt cover; btm 3-2", 2-8". Capacity Design: 0.72 m3 (25.4 ft3). Capacity Working: 0.63 m3 (22.2 ft3). Diameter: 600 mm (23.6 in). Length: 3,800 mm (149.6 in). Height: 2,500 mm (98.4 in). Temperature: 50 °C (122 °F). Pressure: 6 bar (87 psi). Heat Transfer Surface Area: 14.3 m² (153.9 ft²). Orientation: Horizontal. Operational Mode: Continuous. Agitation: Yes. Jacket Material: Stainless Steel 304. Jacket Pressure: 7 bar (101.5 psi). Jacket Temperature: 50 °C (122 °F).
rotary vacuum dryer shaft 200mm diameter paddle rotation 1356mm diameter Exe Grp 1,2,3. Belt and pulley to gearbox Paddle clearance to dryer wall 5mm. Openings: top 3-419mm (16"); 1-200mm center bottom outlet. Capacity Design: 6 m3 (211.9 ft3). Capacity Working: 4 m3 (141.3 ft3). Diameter: 1,400 mm (55.1 in). Length: 4,040 mm (159.1 in). Height: 2,000 mm (78.7 in). Temperature: 200 °C (392 °F). Pressure: 6 bar (87 psi). Shaft Cored and National Board Stamped: Yes. Agitation: Yes. Agitation Seal Type: Packing. Jacket Pressure: 8 bar (116 psi). Jacket Temperature: 200 °C (392 °F).
20 torr @ 80-100 degrees C Chamber size 1'10" diameter x 2' straight side Chamber designed to rotate with piston type vacuum pump Capacity Design: 1 m3 (35.3 ft3). Capacity Working: 0.4 m3 (14.1 ft3). Diameter: 558.8 mm (22 in). Length: 609.6 mm (24 in). Height: 1,829 mm (72 in). Temperature: 100 °C (212 °F). Pressure: 0.03 bar (0.38 psi). Jacket Material: Stainless Steel 316. Jacket Pressure: 10 bar (145 psi). Jacket Temperature: 120 °C (248 °F).
Rotary vacuum dryer shell 750mm diameter x 2500mm long Openings: top 3-400mm; 1-250mm center bottom Heating area approx 4.9 square meter Capacity Design: 1.1 m3 (38.8 ft3). Capacity Working: 0.66 m3 (23.3 ft3). Diameter: 750 mm (29.5 in). Length: 2,500 mm (98.4 in). Pressure: 3 bar (43.5 psi). Heat Transfer Surface Area: 4.9 m² (52.7 ft²). Jacket Pressure: 3 bar (43.5 psi).
rotary vac dryer 32" dia x 10' long shell. Bolt flat heads 12" dia charge port, 12" center btm discharge Approx 10" dia SS hollowshaft. 69.4 ratio Capacity Design: 1.56 m3 (55 ft3). Capacity Working: 1.13 m3 (40 ft3). Diameter: 812.8 mm (32 in). Length: 3,048 mm (120 in). Temperature: 148.9 °C (300 °F). Pressure: 3.8 bar (55 psi). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Agitation: Yes. Jacket Material: Carbon Steel.
54" dia x 10' long shell 16" dia charge port w/cover, 16" dia hydraulic operated center btm outlet. Bolt flat ends. Approx 8" dia SS hollowshaft w/SS paddles. Capacity Design: 3.8 m3 (133 ft3). Capacity Working: 2.8 m3 (100 ft3). Diameter: 1,372 mm (54 in). Length: 3,048 mm (120 in). Orientation: Horizontal. Agitation: Yes. Jacket Material: Carbon Steel. Jacket Pressure: 3.4 bar (50 psi). Jacket Temperature: 204.4 °C (400 °F).
Rotary vacuum dryer 54" dia x 10' long shell. 16" dia charge port w/cover 10" center btm outlet. Bolt flat heads w/2-4" end discharge. 16" x 22" end opening w/bolt cover. Approx 8" x 8" sq hollowshaft w/SS paddles, gear driven. No motor. Capacity Design: 3.8 m3 (133 ft3). Capacity Working: 2.8 m3 (100 ft3). Diameter: 1,372 mm (54 in). Length: 3,048 mm (120 in). Orientation: Horizontal. Agitation: Yes. Jacket Material: Carbon Steel.
w/single ribbon type agit no int rating 32" dia x 8' long shell Bolt flat heads w/1-2" opening 16" dia charge port 12" dia center btm discharge No drive or motor Capacity Design: 1.13 m3 (40 ft3). Capacity Working: 0.85 m3 (30 ft3). Diameter: 812.8 mm (32 in). Length: 2,438 mm (96 in). Orientation: Horizontal. Agitation: Yes. Jacket Material: Carbon Steel. Jacket Pressure: 3.4 bar (50 psi). Jacket Temperature: 148.9 °C (300 °F).
Designed to German TUV standards, With 1.4571 limpet coil jacket on straight side only, full vacuum internal, 20 bar on cored shaft Shaft volume 1000 liter. Shell 1600mm diameter x 4000mm long Shaft cored for heating/cooling Paddles are cored and equipped with scrapers. Openings: top 1-600mm, 1-400mm, 1-125mm, 2-40mm; 1-200mm center bottom outlet. With gear reducer Capacity Design: 7.7 m3 (272.3 ft3). Capacity Working: 6 m3 (211.9 ft3). Diameter: 1,600 mm (63 in). Length: 4,000 mm (157.5 in). Temperature: 200 °C (392 °F). Pressure: 6 bar (87 psi). Shaft Cored and National Board Stamped: Yes. Agitation: Yes. Jacket Material: Stainless Steel Austentic. Jacket Pressure: 20 bar (290.1 psi). Jacket Temperature: 200 °C (392 °F). Jacket Type: Half Pipe/Limpet.
1.4541 (321SS) vacuum paddle jacket dryer system TUV standards Dryer rated full vacuum internal shell 5 bar @ 250 degree C shaft and paddles 5 bar @ 250 degree C heads 5 bar @ 250 degree C, dome 5 bar @ 250 degree C. Shaft 440mm diameter 5.0 KW, 3/50/220/380 volt Cored for heating/cooling with (16) cored paddles @ 1195mm diameter. Dryer has end discharge 400mm x 400mm with discharge valve assembly gear driven Capacity Design: 4.7 m3 (166 ft3). Capacity Working: 3.1 m3 (109.5 ft3). Diameter: 1,250 mm (49.2 in). Length: 4,000 mm (157.5 in). Height: 1,750 mm (68.9 in). Temperature: 250 °C (482 °F). Pressure: 5 bar (72.5 psi). Shaft Cored and National Board Stamped: Yes. Agitation: Yes. Dust Collection: Yes. Jacket Material: Carbon Steel. Jacket Pressure: 5 bar (72.5 psi). Jacket Temperature: 250 °C (482 °F).
HSB # 3332A Shell rated full vacuum 4' diameter x 10' long chamber Has 24" diameter cored removable shaft with paddles and bolt-on scraper blades. 3" Johnson rotary joint. Has 12" diameter bottom outlet with hinged swing bolt cover. 2-12" feed ports. Capacity Design: 3.5 m3 (125 ft3). Capacity Working: 2.3 m3 (82 ft3). Diameter: 1,219 mm (48 in). Length: 3,048 mm (120 in). Shaft Cored and National Board Stamped: Yes. Agitation Seal Type: Packing. Jacket Pressure: 3.4 bar (50 psi). Jacket Temperature: 148.9 °C (300 °F).
wetted parts ST37 (CS jacket) jacketed vacuum paddle dryer DN 21792 internal pressure -1/3 bar @ 250 degrees C, 6000 liter; Jacket pressure 10 bar @ 250°C, c/steel jacket. 419 mm diameter Openings include: top 3-400mm; bottom 1-310mm. Capacity Design: 6 m3 (211.9 ft3). Capacity Working: 4 m3 (141.3 ft3). Diameter: 1,400 mm (55.1 in). Length: 3,935 mm (154.9 in). Height: 1,900 mm (74.8 in). Temperature: 250 °C (482 °F). Pressure: 3 bar (43.5 psi). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Agitation: Yes. Jacket Material: Carbon Steel. Jacket Pressure: 10 bar (145 psi). Jacket Temperature: 250 °C (482 °F).
double ribbon rotary vacuum dryer internal pressure rated by -1/0.5bar @ 300 degrees C, jacket pressure rated by 6bar @ 300 degrees C (volume 525liter) type eAM250MZ4EX 3~/50Hz/500V/1485rpm ExeG3, openings dryer top: (1) DN50, (1) DN80, (2) DN250, (1) DN500, (2) DN600 manway with cover, dryer bottom: (2) DN50 and (1) DN250, openings jacket top: (4) DN50, jacket side wall: (4) DN50, jacket bottom: (4) DN50 with a 1470liter carbon steel filter, manufactured by Harbich, serial number 9086, internal pressure rated by 3bar @ 240 degrees C, flange mounted on dryer top, including some accessories. With approximately 10 m3 dust collector, CS construction. designed to hold 12 filter cartridges'. Capacity Design: 10 m3 (353.1 ft3). Capacity Working: 6.6 m3 (233.1 ft3). Diameter: 2,000 mm (78.7 in). Length: 3,511 mm (138.2 in). Height: 2,400 mm (94.5 in). Temperature: 300 °C (572 °F). Pressure: 0.5 bar (7.3 psi). Dust Collection: Yes. Jacket Material: Carbon Steel. Jacket Pressure: 6 bar (87 psi). Jacket Temperature: 300 °C (572 °F).
jacketed rotary vacuum paddle dryer with 1.7 square meter filter (900 liter) (74 liter) max working temperature 200 degree C, 316L stainless steel chamber 790mm diameter x 1290mm straight side weld dished end with carbon steel jacket, (1) bolt dished end with carbon steel jacket, 316L stainless steel plow blades on shaft 3/50/500 volt openings: top of straight side: 1-500mm with 1.7 square meter stainless steel jacketed filter, 1-250mm, 5-25mm (jacket), bottom: 1-300mm with valve, 4-25mm (jacket) filter pressure 5 bar @ 174 degrees C (900 liter) weld dished top, carbon steel jacket, openings: top 1-100mm, straight side 1-400mm manway, jacket 2-25mm, Dryer and filter TUV certified Capacity Design: 0.9 m3 (31.8 ft3). Capacity Working: 0.6 m3 (21.2 ft3). Diameter: 700 mm (27.6 in). Length: 1,600 mm (63 in). Height: 3,400 mm (133.9 in). Temperature: 174 °C (345.2 °F). Pressure: 5 bar (72.5 psi). Agitation: Yes. Jacket Material: Carbon Steel. Jacket Pressure: 8 bar (116 psi). Jacket Temperature: 174 °C (345.2 °F).
Littleford plow Mixer/Dryer system. National Board Serial number 12025 Rated for the following: Shell, Full Vacuum internal gear reducer Manufactured by Falk, model # 4207509, rated for 9.492:1 ratio Hostile Environment High Efficency AC but no chopper is installed with this blender. With mixer dryer is a vacuum system manufactured by Travani Pumps. Serial # A5934, Type: PLM3315C-A3. Vacuum system includes a water seal vacuum pump, controls, knock out pot and cooler for seal water. Capacity Design: 0.17 m3 (6 ft3). Capacity Working: 0.13 m3 (4.6 ft3). Diameter: 495.3 mm (19.5 in). Length: 660.4 mm (26 in). Height: 2,388 mm (94 in). Orientation: Vertical. Operational Mode: Batch. Number of Choppers: 1. Dust Collection: Yes. Jacket Pressure: 5.2 bar (75 psi). Jacket Temperature: 160 °C (320 °F).
vacuum paddle dryer with dust filter and heated shaft Order number: 14.-235/24158/00000/2-2871/53 Internal pressure rating -1/+0,5 bar @ 151 degrees C operating temperature (total volume 11.000 liter) straight side jacket pressure rated 6 bar @ 151 degrees C (volume 340 liter) Serpentine (2) 1/2 pipe coil jackets each coil rated 6 bar @ 151 degrees C (volume 50 liter); heated shaft rated 6 bar @ 151 degrees C ( volume 1120 liter) (1) bolted for shaft removal; with 3 zone jacket on straight side and 1/2 pipe coil jacket on each head Agitator shaft is 600 mm diameter and has has paddle agitators with flat blades, mechanical seals, and a rotary joint on one end for heating the shaft. Driven through a shaft mounted gear reducer Bag filter mounted on top of dryer housing. Openings include: Top - (1) 1000 mm diameter opening for bag filter, (1) 600 mm feed opening, (1) 500 mm manway with cover; center bottom outlet, 340 mm ID / 420 mm OD With Titanium Grade 2 vertical jacketed dust filter, 10 m3 (353 cubic foot) and 18 cages for filters/ socks. 1000 mm diameter x 2400 mm high, with assist top cover for sock replacement Capacity Design: 10 m3 (353.1 ft3). Capacity Working: 6 m3 (211.9 ft3). Diameter: 2,000 mm (78.7 in). Length: 3,770 mm (148.4 in). Height: 3,800 mm (149.6 in). Temperature: 151 °C (303.8 °F). Pressure: 0.5 bar (7.3 psi). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Agitation: Yes. Agitation Seal Type: Mechanical. Dust Collection: Yes. Jacket Pressure: 6 bar (87 psi). Jacket Temperature: 151 °C (303.8 °F). Jacket Type: Half Pipe/Limpet.
Rotary vacuum paddle dryer system system includes tanks, filters, pumps and other ancillaries Capacity Design: 2.2 m3 (78.4 ft3). Capacity Working: 1.6 m3 (56.5 ft3). Diameter: 1,500 mm (59.1 in). Length: 3,985 mm (156.9 in). Height: 2,950 mm (116.1 in). Temperature: 165 °C (329 °F). Heat Transfer Surface Area: 5.1 m² (55.2 ft²). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Operational Mode: Batch. Agitation: Yes. Dust Collection: Yes. Jacket Material: Stainless Steel Other. Jacket Pressure: 6.5 bar (94.3 psi). Jacket Temperature: 165 °C (329 °F). Jacket Type: Half Pipe/Limpet.
jacketed vacuum paddle dryer system design pressure internal vacuum @ 165 degrees C (2223 liter total capacity), heating capacity internal 3.5 square meter, jackets 1.63 square meter, paddle 3.38 square meter paddle cored for heating, paddle speed 4 rpm 11 kw, 3/50/380 volt, 1450 rpm motor front hinged door with half pipe coil jacket, system includes: (1) 630 liter 316L stainless steel vertical pressure tank, internal pressure 2 bar + vacuum @ 200 degrees C, 1m diameter x 790mm straight side, weld dished top and bottom, (1) 1.6 square meter 316L stainless steel vertical jacketed dust filters, 448mm diameter x 1632mm overall height, weld dished top, weld coned bottom, half pipe coil jacket Capacity Design: 2.2 m3 (77.7 ft3). Capacity Working: 1.6 m3 (56.5 ft3). Diameter: 1,500 mm (59.1 in). Length: 3,985 mm (156.9 in). Height: 2,950 mm (116.1 in). Temperature: 165 °C (329 °F). Heat Transfer Surface Area: 5.1 m² (55.2 ft²). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Operational Mode: Batch. Agitation: Yes. Dust Collection: Yes. Jacket Material: Stainless Steel Other. Jacket Pressure: 6.5 bar (94.3 psi). Jacket Temperature: 165 °C (329 °F). Jacket Type: Half Pipe/Limpet.
jacketed rotary vacuum dryer 3/50/380 volt Cleveland 63-55:1 ratio 3.8 HP, 1750 rpm gearbox shaft cored for steam heating, no national board, rated 50 psi @ 300 degrees F (1-straight side and 1-each end) Rotary union joint, outboard bearings. Unit with dust collector. Openings: top (2) 3' x 18 1/2" hinged access covers with counter balanced mechanism, 2-12"; end 1-8"; bottom 1-10" with manual open/close mechanism; jacket 4-6", 4-2", 4-1", 4-3/4"; shaft 1-2", 1-1 1/2". Capacity Design: 7 m3 (247.2 ft3). Diameter: 1,219 mm (48 in). Length: 6,096 mm (240 in). Temperature: 148.9 °C (300 °F). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Operational Mode: Batch. Agitation: Yes. Dust Collection: Yes. Jacket Material: Carbon Steel. Jacket Pressure: 3.4 bar (50 psi). Jacket Temperature: 148.9 °C (300 °F).
jacketed rotary vacuum paddle dryer safe operating pressure of vessel atmospheric/vacuum 3000 liter with rotary union joint top mounted dust filter, bottom discharge with valve, Capacity Design: 3 m3 (105.9 ft3). Capacity Working: 2 m3 (70.6 ft3). Diameter: 1,250 mm (49.2 in). Length: 3,000 mm (118.1 in). Pressure: 1.01 bar (14.7 psi). Orientation: Horizontal. Operational Mode: Batch. Agitation: Yes. Jacket Material: Stainless Steel 321. Jacket Pressure: 6 bar (87 psi).
internal design pressure -1/3.2 bar @ 200 degrees C (10000 liter), jacket 6 bar @ 200 degrees C (420 liter) jacketed rotary vacuum paddle dryer shaft/paddle 3 bar @ 200 degrees C (520 liter) (1) weld dished end, (1) bolt dished end paddle belt driven by 30kw motor, paddle speed 3 rpm paddle is cored for steam heating, rotary union joint, center bottom outlet Capacity Design: 10 m3 (353.1 ft3). Capacity Working: 6.7 m3 (236.6 ft3). Diameter: 1,794 mm (70.6 in). Length: 4,491 mm (176.8 in). Temperature: 200 °C (392 °F). Pressure: 3.2 bar (46.4 psi). Shaft Cored and National Board Stamped: Yes. Agitation: Yes. Jacket Material: Stainless Steel 316. Jacket Pressure: 6 bar (87 psi). Jacket Temperature: 200 °C (392 °F). Jacket Type: Half Pipe/Limpet.
jacketed rotary vacuum paddle dryer internal design pressure -1 bar @ 200 degrees C (10000 liter) coil jacket 6 bar @ 200 degrees C (420 liter) rotor/paddle 6 bar @ 200 degrees C (520 liter), (1) weld dished end (drive), (1) bolt dished end rotor/paddle with union joint center bottom discharge Capacity Design: 10 m3 (353.1 ft3). Capacity Working: 6.7 m3 (236.6 ft3). Diameter: 1,794 mm (70.6 in). Length: 5,154 mm (202.9 in). Height: 2,600 mm (102.4 in). Temperature: 200 °C (392 °F). Pressure: 1 bar (14.5 psi). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Operational Mode: Batch. Jacket Material: Carbon Steel. Jacket Pressure: 6 bar (87 psi). Jacket Temperature: 200 °C (392 °F). Jacket Type: Half Pipe/Limpet.
jacketed rotary vacuum dryer shaft 50 psi @ 300 degrees F (3) carbon steel jackets (1-straight side and 1-each end) Rotary union joint, outbaord bearings Openings: top (2) 3' x 18 1/2" hinged covers with counter balanced mechanism, 2-12"; end 1-8"; botttom 1-10" with manual open/close mechanism; jkt 4-6", 4-2", 4-1", 4-3/4"; shaft 1-2", 1-1 1/2" Capacity Design: 7 m3 (247.2 ft3). Diameter: 1,219 mm (48 in). Length: 6,096 mm (240 in). Temperature: 148.9 °C (300 °F). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Operational Mode: Batch. Agitation: Yes. Dust Collection: Yes. Jacket Material: Carbon Steel. Jacket Pressure: 3.4 bar (50 psi). Jacket Temperature: 148.9 °C (300 °F).