Quote Cart
Type: Dryer-Thermal Disc
Manufacturer: Bepex
Model: TD48-9
Condition: Unused
Material: Carbon Steel
Diameter: 1,219 mm (48 in)
Length: 2,743 mm (108 in)
Bepex Torus Disc Cooler
U shaped trough, continuous design.
Certified by Moorhead Machinery & Boiler Co
Moorhead Serial number 605-2300.
Shell rated 15 psi @ 350 degrees. No jacket on trough.
U shaped trough, bolted flat top, with one end bolted for rotor removal. Inside dimensions 48” ID x 9’ long
Nominal 106 cubic foot working capacity, approx.
Unit has a tubular rotor with hollow discs mounted on the rotor to allow heating/cooling media to flow through the rotor. The shaft is mounted on outboard bearings, rotary joint on one end, packing glands. Chain and sprocket drive with a gear reducer and 25 HP 3/60/230/460 volt motor. 15 RPM shaft speed.
The residence time is adjustable by and overflow weir at the discharge end.
Height: 1,981 mm (78 in). Number of Disc Shafts: 1. Vessel Temperature: 176.7 °C (350 °F). Disc Temperature: 176.7 °C (350 °F). Vessel Pressure: 1.03 bar (15 psi). Disc Pressure: 6.9 bar (100 psi). Operational Mode: Continuous. Heat Transfer Surface Area: 42.7 m² (460 ft²).
Type: Dryer-Thermal Disc
Manufacturer: Bepex
Model: TD48-9
Condition: Unused
Material: Carbon Steel
Diameter: 1,219 mm (48 in)
Length: 2,743 mm (108 in)
Bepex Torus Disc Cooler
U shaped trough, continuous design.
Certified by Moorhead Machinery & Boiler Co
Moorhead Serial number 605-2299.
Working pressure in the hollow rotor is 100 PSI @ + 50 to 350 degrees F
Shell rated 15 psi @ 350 degrees. No jacket on trough.
U shaped trough, bolted flat top, with one end bolted for rotor removal. Inside dimensions 48” ID x 9’ long
Nominal 106 cubic foot working capacity, approx.
Unit has a tubular rotor with hollow discs mounted on the rotor to allow heating/cooling media to flow through the rotor. The shaft is mounted on outboard bearings, rotary joint on one end, packing glands. Chain and sprocket drive with a gear reducer and 25 HP 3/60/230/460 volt motor. 15 RPM shaft speed.
The residence time is adjustable by and overflow weir at the discharge end.
Height: 1,981 mm (78 in). Number of Disc Shafts: 1. Vessel Temperature: 176.7 °C (350 °F). Disc Temperature: 176.7 °C (350 °F). Vessel Pressure: 1.03 bar (15 psi). Disc Pressure: 6.9 bar (100 psi). Operational Mode: Continuous. Heat Transfer Surface Area: 42.7 m² (460 ft²).
Type: Dryer-Thermal Disc
Manufacturer: Bepex
Model: Model 60-14
Condition: Unused
Material: Carbon Steel
Diameter: 1,753 mm (69 in)
Length: 4,496 mm (177 in)
Torus disc dryer The rotor is 60" diameter x 14' long, and is hard faced. The rotor is cored for steam heating Heating medium is steam Trough is 69" wide x 177" long x 84" high with a vapor dome. Total height with dome cover is 154" high. Panel coil jacket on 25% of the dome cover. Continues product flow with retention time is controlled by adjustable product discharge weir. Rotor had hollow discs, and is chain and sprocket drive Outboard bearings, packing glands with N2 seal purge, Johnson rotary joint on shaft.
Height: 3,912 mm (154 in). Number of Disc Shafts: 1. Vessel Temperature: 85 °C (185 °F). Jacket Temperature: 196.1 °C (385 °F). Vessel Pressure: 1.03 bar (15 psi). Jacket Pressure: 13.1 bar (190 psi). Hood/Cover: Yes. Operational Mode: Continuous. Heat Transfer Surface Area: 114.7 m² (1,235 ft²).
Thermal disc dryers use a series of heated, rotating discs mounted on a central shaft to indirectly dry sludge, slurries and other semi-solid materials. These systems provide efficient thermal contact between the material and the heat source, allowing for rapid evaporation without direct flame or high air volume. With over 47 years of experience, IPP offers secondhand and surplus disc dryers from 20 global process plant sites, backed by more than 15,000 in-stock equipment systems.
Disc dryers are often used in industries where thermal control, emission reduction, and minimal oxidation are key. Their compact design makes them space-efficient while delivering high throughput and energy savings.
Thermal disc dryers are built for durability and consistent heat transfer:
Learn more about indirect thermal drying systems from WaterWorld.
Search the IMS inventory or contact IPP’s equipment team to source the right used, secondhand or surplus thermal disc dryer. From wastewater to chemical sludges, IPP helps you save time and money with equipment that’s built to last and ready to ship.