New and Used Equipment

98.6% water evaporation4-effect falling film evaporator system Designed by Fritz Voltz sohn feed rate 3.4m3/hr, product 1.3 m3/hr Feed to 1st evaporator is 3.4 m3/hr @ 34.8% concentration and @ 104 deg C vacuum @ 4th evaporator 130 mbar Evaporator concentrations are: 1st = 42.1% @ 116 deg C2nd = 55.8% @ 107 deg C, 3rd = 91.3% @ 81 deg C, 4th = 98.6% @ 98 deg C System consists of:(3) 46 square meter 316 stainless steel tube, head and shell falling film evaporator (1st , 2nd, 3rd effects), manufactured by APV, design pressure tubeside 0.69 bar + full vacuum @ 130 degrees C, shell 3.10 bar + full vacuum @ 140 degrees C, working pressure tubeside 0.207 bar @ 120 degrees C, shell 2.07 bar @ 130 degrees C, (44) 50mm diameter x 18 SWG X 7m long 316 stainless steel tubes, 316 stainless steel tube sheets, 560mm diameter 316 stainless steel shell with expansion joint, (1) 316 stainless steel bonnet head, (1) bolt dished bottom head, mounted on a carbon steel skirt(1) 6 square meter 316 stainless steel tube, head and shell falling film evaporator (4th effect), manufactured by APV, design pressure tubeside 2.5 bar + full vacuum @ 150 degrees C, shell 2.5 bar + full vacuum @ 150 degrees C, (14) 44mm diameter x 16G x 3.5m long 316 stainless steel tubes, 323.9mm diameter 316 stainless steel shell with expansion joint, 4295mm overall height, (1) 316 stainless steel flat bonnet head, (1) weld coned bottom, effect attached on top of a 720 liter 316 stainless steel vertical pressure separator/tank, manufactured by APV, design pressure 2.5 bar + full vacuum @ 250 degrees C, 792mm diameter x 1.5m straight side, weld dished top and bottom, mounted on legs(3) approx 600 liter 316 stainless steel vertical separators, manufactured by APV, design pressure 10 psig + full vacuum @ 130 degrees C, 775mm diameter x 1219mm straight side, weld slight coned top, weld coned bottom,(1) 10.6 square meter 316 stainless steel tube and shell horizontal condenser (1st stage), manufactured by APV, design pressure tubeside 2.5 bar + full vacuum @ 150 degrees C, shell 2.5 bar + full vacuum @ 150 degrees C, (34) 25mm diameter x 16G x 4m long 316 stainless steel tubes, (2) 316 stainless steel flat heads, 406mm diameter 316 stainless steel shell, 4.5m overall length, mounted on saddles(1) 11 square meter 316 stainless steel tube and shell horizontal condenser (2nd stage), manufactured by APV, working pressure tubeside 2.07 bar @ 35 degrees C, shell -0.9 bar + full vacuum @ 50 degrees C, (76) ¾” x 18 swg x 4145mm long 316 stainless steel tubes, (2) 316 stainless steel flat heads, 300mm diameter 316 stainless steel shell, overall length 4523mm, mounted on saddles,(3) approx 132 liter 316 stainless steel vertical pressure tanks (flash vessel), manufactured by APV, design pressure 2.5 bar + full vacuum @ 150 degrees C, 400mm diameter x 750mm straight side, bolt dished bonnet head, weld dished bottom, mounted on legsProcess operationThe first 3 evaporators are falling film and tube (shell & tube) evaporators, where the product flows up and down through a series of tubes which are surrounded by a heating medium, steam @ 1.8 bar is used as the heating mediumThe hot liquid from each evaporator is fed to its associated “separator” in which the vapour separates from the liquid and is drawn off,The 4th evaporator uses a “once-through” falling film concentrator, the unit is similar to that of a shell & tube heat exchanger except that the product falls down the unit through a number of pipes which are surrounded by a heating medium, steam @ 1.8 bar is used as the heating medium, Vacuum @ 130mbar is applied to the 4th evaporator, which draws the vapour through the first 4 evaporators.After the 4th evaporator the product is fed through a heat exchanger, where it cools the product to between 50 deg C and 70 deg C, water is used as a cooling medium, from there the product goes to storage tanks (not available)

• Vessel constructed of ASTM A353 (DIN 1.5662 / X8Ni9) nickel alloy specially designed for cryogenic & low temperature operations.
• 59,043 liter (15,600 gal.) inner vessel.
• 26,370 liter (6,966 gal.) space between tanks insulated with powdered perlite held under -1 bar vacuum at 20 deg. C.
• Outer sheathing constructed of ASTM A283 Grade C (DIN RSt37-2) carbon steel.
• With (9) fin stainless steel 18.5 liter air heater mounted under tank bottom dish.
• With thermosyphon on bottom dish.
• Outer sheathing 12mm thick shell, 8mm thick head.
• With FlowServe DN 150 globe valve.

• Vessel constructed of ASTM A353 (DIN 1.5662 / X8Ni9) nickel alloy specially designed for cryogenic & low temperature operations.
• 59,043 liter (15,600 gal.) inner vessel.
• 26,370 liter (6,966 gal.) space between tanks insulated with powdered perlite held under -1 bar vacuum at 20 deg. C.
• Outer sheathing constructed of ASTM A283 Grade C (DIN RSt37-2) carbon steel.
• With (9) fin stainless steel 18.5 liter air heater mounted under tank bottom dish.
• With thermosyphon on bottom dish.
• Outer sheathing 12mm thick shell, 8mm thick head.
• With FlowServe DN 150 globe valve.

• Vessel constructed of ASTM A353 (DIN 1.5662 / X8Ni9) nickel alloy specially designed for cryogenic & low temperature operations.
• 59,043 liter (15,600 gal.) inner vessel.
• 26,370 liter (6,966 gal.) space between tanks insulated with powdered perlite held under -1 bar vacuum at 20 deg. C.
• Outer sheathing constructed of ASTM A283 Grade C (DIN RSt37-2) carbon steel.
• With (9) fin stainless steel 18.5 liter air heater mounted under tank bottom dish.
• With thermosyphon on bottom dish.
• Outer sheathing 12mm thick shell, 8mm thick head.
• With FlowServe DN 150 globe valve.

1.5m wide x 24.85m long rotoform cooling conveyor/belt Drawing Number 6530. 5m long hot water section 17.5m cooling water section Cooling water capacity: 185 GPM @ 30 psi, Hot water zone has 16 sprays x 4 runs x 0.71 gpm (45.4 gpm), Cold water zone has 49 sprays x 4 runs x 0.71 gpm (139.1 gpm), 900mm diameter tension drum, 900mm diameter drive drum andvik Dropformer feed unit with hot oil heated weir, chain driven by 0.75 KW, 3/50/415 volt motor via varispeed gearbox. brass knife discharge, carbon steel support frame with sump tanks mounted under the belt, Flaker includes a discharge vibratory shaker for size classifacation, (3) Sihi Centrifugal cooling water pumps, Russel Finex inline water filter,

450mm diameter Liquid/Liquid separator system, designed for separating oil and solvents manufactured by Ott AG, with a stainless steel cyclone separator, openings: on the top (1) 35mm, (1), 45mm, (1) 65mm, (1) DN 100, on the side (1) DN50, (1) DN150 with sight glass, with (2) horizontal stainless steel stripper tanks built 1978 manufactured by EDAK, first tank, serial number 2040/1 rated @ 2 bar by 200 degrees C, volume 200 liter, openings: (1) 35mm, (1) 65mm, (2) 100mm, (1) DN 150 with sight glass, second tank, serial number 2040/2 rated @ 2 bar by 200 degrees C, volume 250 liter, openings: (1) 35mm, (1) 65mm, (2) 100mm, (1) DN 200 with sight glass, with (3) Plate heat exchangers manufactured by Ott, first heat exchanger with 18 plates, second heat exchanger with 19 plates, third heat exchanger with 27 plates, with a centrifugal pump manufactured by Fristan, type FP732/155L, serial number 32121533 driven by a 4,6kW electrical motor manufactured by Loher, type EA132S1A-2, serial number 8475071, 3~/50Hz/380V @ 2915rpm. Originally used to seperate Heptane and Oil. All Stainless Steel construction.

4000 Liter/Hr.(17 GPM) clean in place skid Skid contains the following major pieces, one condenser, two tanks, two pumps, and a on board control panel. Two 400 Liter tanks with open tops and welded slight cone bottoms.(Solution supply & return tanks) two sanitary centrifugal pumps by Inoxpa, and controls with a Siemens HMI. Heating capacity 4000 Liters/hr., Heat transfer area 0.9 m2, Temp rise 50 -60 degrees C, steam consumption per hour 80 kg/hr

disperser/disolver 50mm diameter x 800mm long shaft with 350mm diameter double saw tooth blade 470-1700 rpm shaft speed built on controls, with bowl holding/clamping mechanism, can use 250 ltr upt to 600 ltr bowls/tanks

Rotary vacuum paddle dryer system system includes tanks, filters, pumps and other ancillaries Dust Collection: Yes. Jacket Material: Stainless Steel Other. Jacket Pressure: 94.3 psi. Jacket Temperature: 329 °F. Jacket Type: Half Pipe/Limpet.

System includes Sulzer Burckhardt 316 stainless steel water seal vac pump, Type PMZF-3817-C9/X3-1986 Pump rated 56 liter/min. Driven by 20 KW, 3/50/500 volt, 975 rpm motor. (1) rubber lined receiver. (1) 600 liter plastic tanks, 1000mm diameter x 900mm straight side, bolt top, weld dish bottom. Openings: top 1-250mm, 2-200mm, 4-80mm; 1-80mm center bottom outlet Haug oil free air compressor Type BO-75-D4-ASW driven by 2.2 KW 3/50/500 volt 1400 rpm motor

product contact, MF,UF, RO system Design parameters of the MF system feed flow is ~ 6.5 Kl./hr. with a permeate flow of ~6.0 Kl./Hr. Bleed out(reject) rate is 0.5 Kl./Hr Design parameters of the UF system, 10 kg/cm2 operating pressure, 6-12 degrees C temperature, feed flow is ~ 6.0 Kl./hr., with a permeate flow of ~4.5 Kl./Hr. Bleed out(reject) rate is 1.5 Kl./Hr. Design parameters of the RO system are as follows:40 bar(max) operating pressure, 6-12 degrees C. temperature, feed flow is ~ 1.5 Kl./hr., with a permeate flow of ~0.9 Kl./Hr. Bleed out(reject) rate is 0.6 Kl./Hr Designed for CIP and sanitizing steaming System contains pressure vessels, tanks, heat exchangers and pumps with interconnecting piping Skid mounted with electronic PLC controls

5 m3/h, water purification system with 4000 liter purified water storage. 316L stainless steel water purification and demineralized water system, generated by reverse osmosis and electrode ionization, purified water flow rate 10 m3/hour, demineralized water flow rate 5 m3/hr, system consists of 2-skids, equipment includes (2) 170 liter resin softener tanks, (1) plate heat exchanger, filters, pumps, UV generators, (1) 4000 liter purified water distribution tank, (1) 1500 liter demineralized water distribution tank, (1) 1000 liter recirculation tank and other ancillaries