Stainless Steel 304 Buflovak/Blaw Knox Dryer-Rotary Vacuum - IPP# 108064

Type: Dryer-Rotary Vacuum

Manufacturer: Buflovak/Blaw Knox

Condition: Used

Material: Stainless Steel 304

Capacity Design: 1.56 m3 (55 ft3)

Capacity Working: 1.13 m3 (40 ft3)

rotary vac dryer 32" dia x 10' long shell. Bolt flat heads 12" dia charge port, 12" center btm discharge Approx 10" dia SS hollowshaft. 69.4 ratio

Diameter: 813 mm (32 in). Length: 3,050 mm (120 in). Temperature: 148.9 °C (300 °F). Pressure: 3.8 bar (55 psi). Rated for Vacuum: Yes. Heat Transfer Surface Area: 7.8 m² (84 ft²). Shaft Cored and National Board Stamped: Yes. Orientation: Horizontal. Agitation: Yes. Jacket Material: Carbon Steel.

Type: Dryer-Rotary Vacuum

Manufacturer: Blaw Knox

Condition: Used

Material: Stainless Steel 304

Capacity Design: 3.5 m3 (125 ft3)

Capacity Working: 2.3 m3 (82 ft3)

4' diameter x 10' long chamber. as 24" cored shaft with paddles and removable scrapers. No drive available. Unit has chain guards for drive. Top openings one 12", one 10 ". Jacket openings are 2" NPT. 12" bottom discharge.

Diameter: 1,200 mm (48 in). Length: 3,050 mm (120 in). Height: 2,150 mm (84 in). Rated for Vacuum: Yes. Heat Transfer Surface Area: 11.7 m² (126 ft²). Agitation Seal Type: Packing. Jacket Material: Carbon Steel.

Type: Dryer-Rotary Vacuum

Manufacturer: American Process Systems

Model: C060/6660

Condition: Used

Material: Stainless Steel 304

Capacity Design: 2.8 m3 (100 ft3)

Capacity Working: 1.7 m3 (60 ft3)

cylindrical design Vessel designed for 14.9 psi and full vacuum rated at 29.92” Hg. This machine is designed for continues operation but was previously used in a batch process. The jacket is two zone style with 3” half pipe. The manufacturer indicated this machine is designed for sanitary applications. The agitator shaft is not cored for heating, 6” diameter 304 SS, with 12, ¾” thick posts and paddles. Paddles are 12” long x 6.5” wide. Agitator clearance is 1/8” nominal at the lowest point. Rotation of the agitator is counter clockwise at 25 rpm. Agitator is driven by a right angle geardrive manufactured by SEW Eurodrive with a 40 Hp AC motor. Model # KAF157DV200L4. The geardrive has a 70.38:1 ratio rotating the output shaft at 25 rpm. The agitator is sealed by two Woodex, fully spit Meco mechanical seals, and rides on two Dodge expansion type flange bearings. Top connections are one 24” flanged nozzle for vacuum filter, one 24” manway, and one 16” loading flange. Discharge nozzle is 8” flanged. Shell is wrapped with 14 Gauge 304 SS, covering 2” thick Ceramawol insulation designed to limit the dryers exterior temperature to <140 degrees F. The baghouse filter is 304 SS, and is 32” in diameter x 62” high. The bottom of the dust collector bolts directly to the dryer by a flange, and the top has a bolted 28” diameter man way for filter changes.

Diameter: 1,100 mm (44 in). Length: 3,050 mm (120 in). Height: 2,150 mm (84 in). Pressure: 1.03 bar (14.9 psi). Heat Transfer Surface Area: 10.7 m² (115 ft²). Orientation: Horizontal. Operational Mode: Continuous. Agitation: Yes. Agitation Seal Type: Mechanical. Jacket Material: Stainless Steel 304. Jacket Pressure: 8.6 bar (125 psi). Jacket Temperature: 218.3 °C (425 °F). Jacket Type: Half Pipe/Limpet.

Type: Dryer-Rotary Vacuum

Manufacturer: VOMM Turbotechnologia

Model: ES 2400

Condition: Used

Material: Stainless Steel 304

Capacity Design: 10 m3 (353.1 ft3)

Capacity Working: 6.6 m3 (233.1 ft3)

304 stainless steel jacketed turbo dryer, water content of dry product @ 0.5% and a dry particle size of >420 microns capacity, gas fired, steam drum type, 304 stainless steel drum, carbon steel rotor with 304 stainless steel lining, 460 volt, 60Hz, 500 rpm turbine speed, operating pressure of drum is slightly below atmospheric @ 180/100 degrees C, jacket 10 bar g @ 175 degrees C, design pressure of jacket 12 bar g @ 220 degrees C, internal blades to keep product on the sidewall and to push product down the dryer, internal self cleaning is done via reverse rotation of the drum

(1) approx 90m3/hr 304 stainless steel blower/fan, manufactured by Chicago Blower, type MPC-2/18, 1.165 kg/m3 Density, 30 degrees C, 3480 rpm, driven by 15kW, 3/60/460 volt, motor

(1) Superheated air generator with gas burner, manufactured by Babcock Wanson, type Mixbloc 500, 500,000 kcal/h, 150-200 degrees C outlet temperature, 0-30 degrees Inlet temperature, 1150 Ncm/hr combustion air delivery, 3000/5000/6000 Ncm/hr min/nor/max primary air delivery, natural gas fired, 60Hz, 460 volt,

Diameter: 1,300 mm (51.2 in). Length: 6,050 mm (238.6 in). Temperature: 400 °C (752 °F). Rated for Vacuum: Yes. Heat Transfer Surface Area: 28.5 m² (306.8 ft²). Orientation: Horizontal. Jacket Material: Stainless Steel 304. Jacket Pressure: 12 bar (174 psi). Jacket Temperature: 220 °C (428 °F). Jacket Type: Standard.