New and Used Equipment

with feed hopper serial #10 486

• DISHO Vacuum Mixing Dispersing and Homogenizing Unit. Vessel manufactured by Hebold, rated FV/36 psi at 356 degrees F internal; with a 24" cone bottom. It has a flanged and bolted dish top head. Vessel openings include: Top -14" manway with hinged cover, (3) 4"; (3) 1".
• Fully insulated with SS shroud over insulation. Mounted on legs with Top mounted double motion agitator with wide sweep with perforated pitched blades and side wall scrapers, and center shaft with perforated pitched blades that intermesh with counter rotating wide sweep agitator blades.
• 3/60/230/460 volt motor Vessel discharges into a horizontal DISHO homogenizing mill, multi chamber, driven by a 51 KW 3/60/230/460 volt motor. Complete skid mounted system with approx. 5 HP water seal vacuum pump, controls and stainless steel enclosure for pump and mill drive.

Size 16Trough dimensions 31" x 49" x 47" deep, hinged cover w/counter balance, w/cored dispersion type mixing blades. Packing gland on shafts Shafts geared both ends and driven by Pacemaker 200/100 HP, 3/60/460 volt, 1770/885 rpm motor, Frame #449T, w/gear reducer. Output rpm on front blade 42/21, rear blade 25/125driven by 5 HP motor.

• Three pass fire tube boiler5021 MBHMBH input 6278Fireside heating surface area is 750 sq. ft Firing rate is as follows: 1000 BTU Gas (MBH) =6277, 140,000 BTU/Gal. Oil (GPH) =44.8Safety valve rated for 6000 psi Boiler has 182, two inch tubes This boiler features FGR and low Nox operation with it's IRI gas train While firing natural gas, emissions levels are are no greater than 30 PPM of NO x This boiler features 3 gas passes that extract the maximum usable heat from the fuel while maintaining optimum flow for forced draft firing It also has easy opening/closing doors that minimize labor and parts cost’s while performing routine maintenance such as cleaning and inspections Water requirements are 6551 pounds of water or 785 gallons Approximate weight wet is 16,251 lbs., approximate dry weight is 9,700 lbs.

twin shaft wad mill (pug mill) with a removable 304SS cover 1/8" thick lining Twin chrome plated mixing shafts, 5" diameter with chrome plated blades, with a CS compacting tapered screw discharge on the end of each shaft . Tapered screw sections are 14" diameter x 36" long, feeding a single 9 3/4" wide x 6" high 304SS lined discharge chute. With an air operated automatic wire cutter on discharge end of machine to cut extruded clay. Screw shafts driven through a 25.38 ratio shaft mounted reducer Motor rated for 230/460 Volts

• Variable speed motor based on load.

UNUSED

Internal finish 240 grit buff polished-Bright polished, external buff polish to a matte finish. ASME NB rated, and "U" stamped.

welded dish heads (2:1) 12 mm thick

Coil: 114 mm OD x 4 mm thick,

Limpet covers bottom dish and 2615 mm of straight side (pitch 150mm). Coil heating surface area.

With Insulation rings and upper drip ring. Two top lifting lugs and one tailing lug.

20" Manhole with Cover and davit arm assist, one 6" sight glass, Support Type: Lugs.

MFR # 12269 Model SA-3000 Special three top lifting lugs, six leg couplings, four side wall lugs Shell=1 & 1/64", heads=1 & 1/64", jacket =5/8" PTE size 10 drive with an EX proof 20 HP motor and a dry seal. 36" main cover. 18" man way with pro ring and sight glass assembly with man way assist.

• Alloy C276 Vacuum Conical Screw Dryer.
• Coil jacket, Shell rated 88FV.
• 103" diameter x 117" length.
• Welded dished top head.
• Orbital acting screw agitation. Johnson Joint attached to top.

RECONDITIONED, Approximately 25 - 30 tonnes of material per hour (dependant on density) cast steel Briquetter very similar in design to Sahut Conreur and Komerak Greaves Roller size: 1.2m diameter, 925 Ovoid type briquettes per revolution briquette size approximately 45mm diameter x 35-40mm thick Twin hydraulic rams 80 tonnes a piece (2500 psi) each side gives a separating force of 320 tonnes English electric main drive motor with a fluid coupling to a two speed W.G.W inline gearbox. Two speed 8.5 or 11 Rpm (at the rolls) Machine has undergone a full refurbishment and is in full working order: As part of the refurbishment the following was done: Gearbox rebuilt and gears refaced where necessary Reconditioned fluid coupling Reconditioned main drive motor and feeder unit motor New Gearbox oil circulation pump Fresh oil in gearbox and transfer box All new hydraulic lines and couplings All four rams are refurbished New safety valves and couplings fitted to the hydraulic power pack Main Bearings disassembled, checked and re-greased (all OK), new lube points/grease nipples installed Main roll surfaces polished and checked Feeder unit was stripped and checked, feed control gates greased. Reconditioned feeder unit motor Fully blasted undercoated and painted Custom made stand as shown Also a custom made out feed hopper to attach to the stand and machine.

Jaygo vacuum dispersion and homogenizing mixer system Mixing chamber rated 20 psi and full vacuum @ 350 degree F to -20 degree F minimum. All fittings sanitary. Unit measures 20" diameter x 20" straight side x 8" cone bottom clamped dished top. Gate design agitator with teflon scraper blades5 rpm minimum, 34 rpm maximum.Drive has automatic hydraulic lift mechanism with 24" lift capacitySystem includes: (1) 3 HP Nash brass vacuum pump, Model #AT34. (1) 1 HP Moyno pump, Model #IFF4SSV, driven by 1 HP Reeves varidrive.(1) approx 5 HP inline disperser.Includes all controls and power box, temperature probes and capacitance probes.

Vacuum dryer system internal pressure rated -1/+1bar @ -10/+165 degrees C (volume 250 liter), jacket pressure rated -1/+8bar @ -10/+165 degrees C (volume 35 liter) type CD180M-4 3~/50Hz/230-400V/1,460rpm CE confirm, EExdeIICT4, system including: (1) 3.1m² 1.4571 stainless steel tube and shell heat exchanger/condenser, (1) 8m³/h @ 3m head iron cast centrifugal pump, (1) 50 liter 1.4571 stainless steel condensate receiver, (1) 20 liter 1.4571 stainless steel gas separator, (1) 17.5 liter 1.4571 stainless steel jacketed pressure tank, (1) Frequency converter on pallet, (2) stainless steel guards on pallet, (2) Valves and (1) chain on pallet, Accessories on pallet Jacket Temperature: 165 °C.

150 Gallon,, vertical dispersion mixing machine with jacketed vessel. Dispersall Mixer Type VP, vessel rated for Full vacuum at 4 psi. Vessel size is 33.5" diameter x 41" deep, with removable top and welded bottom. Mounted on a stand. Two top mounted planetary mixers with Teflon scrapers. One under driven high shear mixer. With Waukesha model 25 SS positive displacement pump, with mechanical variable speed drive. Pump serial # D0261137SS. Overhead gantry for top removal.

Twin Shaft Nara paddle Shell WO Number DS-220, Jacket Serial Number D-258, National Board Number 1102. Heat Transfer area: Jacket 107 Sq Ft, Agitator 293 Sq Ft, total 400 Square Foot. twin shaft with discontinous wedge shaped staggard paddles. Both jacket and agitator rated for 165 psi at 425 degrees F. Indirect heat, by saturated steam heat; rotary joints on shafts with quick disconnects and zero speed switch on end of shaft. Shaft seals are Meco Systems self-aligning externally adjstable, fully split elastomer seal, with purge port. With a 316LSS dome type covered trough rated for 5 psi pressure. With a chain and sprocket drive, SEW Sanasaio Parallel shaft speed reducer and a 75 HP Reliance motor. Motor data, ID # OIMAN 79345 G001 BC Frame 365 T, rated for 1780 rpm, Volts 230/460 amps 172/86 3 ph, Hz 60. Shaft speed approximately 12 RPM. Openings include: 15" x 36" feed opening, (1) 12" diamter vapor opening, (3) 18" x 24" explosion vent openings, (1) 6" Sweep Gas Inlet, (1) 20" x 20" Access hatch with bolted cover, (2) 6" view ports; trough has (1) 12" x 58" flanged discharg opening, (2) externally adjustable weir gates.

Casing rated for 25 psi maximum working pressure.
Standard nozzle orientation motor : 219 amps

• This is a bare reactor

• Trailer mounted set. Oil Type Required API CF-4
• Complete Service at 11207, Hours includes New Batteries, Oil & Filters, Air Filters, Fuel Filters.

• reactor/crystalliser,
• design pressure internal 6 bar + full vacuum @ -29/185 degrees C (12300 liter), jacket 10 bar + full vacuum @ -20/185 degrees C,
• driven by 15kW, 3/50-60/690-400/660-380/415-440 volt, 1467/1463/1471/1763 rpm ATEX EExde IIC T4 IP65 motor,
• 3-sets of 2-blade Viscoprop pitched paddles, 1-set of 2-blade Endorgan pitched paddle on the bottom of the shaft,
• gas type Burgmann double dry running mechanical seal,
• design code: PD5500 - 2006 - module G - gas group 1, CAT 2, CE 0878,

UPZ 315 highly polished 316L stainless steel fine impact mill with pin disc grinding system consisting of:

(1) UPZ 315 highly polished 316L stainless steel pin disc mill, manufactured by Hosokawa, serial #P1 125 630/1, asset #12302, 4500 rpm,(max 9200 rpm), permissible overpressure 0.09 bar @ 50 degrees C, inside 34 liter, pin size 7mm diameter x 35mm long, (236) pins on door side, (231) pins on drive side, plate beater diameter 298mm, (10) plate beaters, mill driven by approx 18kw motor

(1) 13.5 square meter 316L stainless steel vertical heat exchanger (gas cooler), manufactured by Transitherm GmbH, type WTGDP 273/2400 1-PASS, fabrik #10830, design pressure tube side -1/10 bar @ -29/100 degrees C (82 liter), shell side -1/10 bar @ -29/100 degrees C (76 liter), TUV, (132) 14mm diameter x 1 x 2.4m long 316L stainless steel tubes, single pass tube side, 273mm diameter 316L stainless steel shell

(2) 316L stainless steel heads with 90 degree bend, openings tube side each head with a 150mm, shell: 2-75mm, mounted on lugs

(1) stainless steel screw feeder

(1) 22 square meter polished 316L stainless steel reverse jet dust filter, manufactured by Hosokawa Alpine, type AR 34 M, serial #P1 140 710/1, pressure -0.1/+0.49 bar @ -29/80 degrees C, stainless steel polished to Ra max 0.5um, 1.3m diameter x 2m straight side x 1250mm bottom cone section, clamp bonnet head, (34) 130mm diameter x 1820mm long internal filter cages, 6-sets of valves

(1) highly polished 316L stainless steel cantilever rotary sifter, ATEX zone 22, manufactured by Kemutec Powder Technologies Ltd, type K650C sifter, serial #K650C A10942/1, asset #12230, working pressure -0.1/0.49 barg, design temperature 40 degrees C max, driven by 2.2kw, 3/50/415 volt 1500 rpm EExde IIB T4 zone 1 & 22, motor, mounted on a stainless steel frame with wheels

(1) 25m3/hr @ 7.06m head 316L stainless steel centrifugal pump, manufactured by HMD Sealless Pumps, serial #824545, type GSI 80-50-200 D-4A, NPSHa 19.68m, driven by 1.1kw, 3/50/415 volt 1450 rpm EExd IIB T4 motor, mounted on a baseplate

(1) 15 m3/minute 316L stainless steel Radial blower/fan, manufactured by Reitz, type single stage KXE080-001430-00, serial #175747, total pressure increase 746 daPa, impellor speed 3000 rpm, inlet size 140mm, discharge 100mm, driven by 7.5kw, 3/50/415 volt 3000 rpm EExdeIIBT4 motor

(1) 160mm diameter polished 316L stainless steel motorised rotary valve, manufactured by Engelsmann, type ZSA 200, driven by 0.55kw, 3/50/415 volt 10 rpm EExdIICT4 motor

(1x) stainless steel Lowbotech discharge unit with metal detector

(1x) 316L stainless steel Matcon Hopper discharge unit,

Electric air dryer 12 hr dryer cycle 3.6 KW W/50 scfm Nash Mdl AL-574 compressor 10 HP, 3480 rpm motor

Built in Economizer.

15-25kg Paglierani valve bag weigh, bagging and filling line, system consists of: (1) Paglierani weighing, bagging/filling machine with bag shaker as it is filling which Driven by 1.1/1,27kw, 3/50/60/230-400/265-460 volt, 910/1090 rpm ATEX Ex e 11 T4 motor, powder is screw feed into the bag, screw driven by 2.2/2.5 kw, 3/50/60/230-400/265-460 volt, 1420-1690 rpm ATEX Ex e 11 T4 motor bag support mechanism driven by 1.1/1.27 kw, 3/50/50/230-400/265-460 rpm ATEX Ex e 11 T 4 motor, (1) 304 stainless steel feed hopper with screw discharge and 25 liter stainless steel cyclone vacuum powder conveyor, cyclone type VF02, manufactured by Palamatic, serial #B120 203 C_02, -10/40 degrees C, 1-2.5 m3/hr, (1) manually fed bag conveyor (1) bag erector and feeding machine (1) control panel

C 3-stage reciprocating Boil-off-gas (BOG) compressor system maximum allowed rod. Load 100kN, rated discharge pressure of final stage 69 barg, suction pressure 1st stage 0.05 bar @ 30 degrees C, 2nd stage 4.6 bar @ 45 degrees C, 3rd stage 27.7 bar @ 45 degrees C, discharge pressure 1st stage 4.7 bar @ 176 degrees C, 2nd stage 27.9 bar @ 190 degrees C, 3rd stage 69 bar @ 160 degrees C, driven by a 250kw, 3/50/400 volt, 594 rpm ATEX 1022 EExd II B T4Loher motor, (1) 550 liter stainless steel vertical pulsation dampner vessel, manufactured by Nadoba Stabilini, serial #954, pressure 0.05 bar @ -118/+30 degrees C, 610mm diameter x 1740mm straight side, weld dished top and bottom, (1) 125 liter carbon steel horizontal pulsation dampner, manufactured by Tlakova Nadoba Stabilini, serial #955, pressure 10.7/69.6 bar @ 57/159 degrees C, weld dished ends, (1) carbon steel tube and shell horizontal 1st stage intercooler, manufactured by APL Apparatebau AG, serial #W8227/EC22601, tubeside pressure 10 barg @ -10/200 degrees C (27 liter), shell 10 barg @ -10/200 degrees C (53 liter), (1) carbon steel tube and shell horizontal 2nd stage intercooler, manufactured by APL Apparatebau AG, serial #W8228/EC22602, tubeside pressure 29 barg @ -10/200 degrees C (20 liter), shell 10 barg @ -10/200 degrees C (55 liter), (1) carbon steel tube and shell horizontal 3rd stage intercooler, manufactured by APL Apparatebau AG, serial #W8229/EC22603, tubeside pressure 78 barg @ -10/200 degrees C (9 liter), shell 10 barg @ -10/200 degrees C (42 liter), system also includes interconnecting pipework, valves, etc, ALL CE MARKED