Nash SC2SS Vacuum pump, with vapor recovery system
Test # 90Y002
The system includes the following equipment; a vacuum pump, two heat exchangers, a separating tank, and seal pots. The direct drive vacuum pump, is manufactured by Nash, size SC2SS, Pos. 4 ,Vac, rated 200 cfm @ 5-20" Hg.
The vapor exchanger is a 30 sq. ft., all 316 SS, horizontal heat exchanger manufactured by Industrial Process Equipment corp., Model # 2ST8-60, Serial # 105-641A
National Board # 988
It’s shell and tubes are rated for 150/FV
The condensate chiller is a 10 sq.ft., 316SS tube bundle, 316SS heads, with CS shell, horizontal heat exchanger and is also manufactured by Industrial Process Equipment Corporation. Serial # 1056413, and National Board # 989, Rated for 150/FV psi in the shell and tubes.
The dual seal pot arrangement, with Nitrogen purge is provided by Duramettalic, Canada/Condex Heat Transfer Corp. Serial # 91-3-4146 & 4179, and rated for 400 psi at 400 degrees F. Both have level sight glasses and N2 purge line with regulator and Liquid make up valves. The units 316 SS separator, is manufactured by Jenco, Serial # 91-1327, National Board # 525, and rated for 30/FV at 350 psi. The separator tank also has a liquid level sight glass. The vapor inlet line is 4" flanged, and separator outlet is 1”. Automatic valves for liquid flow control are provided by Fisher and El-O-Matic, and the vapor contact piping is 316 SS. System includes all DP cells, RTD temperature probes, and pressure gauges. Designed to be used in a hazardous atmosphere, skid has a 60 amp Square D breaker, and explosion proof switches and controls.

Manufactured by Estrella AG in Ettingen, Germany
Packed column consisting of (3) Clamped mid sections,
each 2.000 mm long x 788 mm inside diameter,
openings each section: (1) NW 150, (1) NW 50;
(1) clamped dished top, 1.120 mm long x 788 mm inside diameter

• Plates are FDA approved and non gasketed.
• Polypropylene plates and frames and all Stainless Steel skeleton.
• Approximately 38 chambers.
• 4 eye closed delivery, 1" inlet and outlets.
• Manual closure with Hydraulic Assist manufactured by SPX. Plate Diameter or Width: 800 mm. Plate Height: 800 mm. Plates Shifted By: Manual.

• Plates are FDA approved- Non Gasketed.
• Polypropylene plates and frames and all Stainless Steel skeleton.
• 44 chambers.4 eye closed delivery,1" inlet and outlet.
• Manual closure with Hydraulic Assist manufactured by SPX. Plate Diameter or Width: 800 mm. Plate Height: 800 mm. Plates Shifted By: Manual.

• Side discharge with automatic valve Agitator Cored for Heating/Cooling: Yes. Vessel Liquid Capacity: 400 gallons.

• New Base Reactor Body (with covers) Bare reactor price in sales comments.
• Can be upgraded w/ drive system to reactor
• Both ASME National Board # and CE Marked
• Interchangeable with UGE Agitation Systems & Pfaudler Agitation Systems

20 Ton , 3000 SCFM Roof top heat and ac system--12 SEER

• Sheathing covering Insulation rock wool and puff , 304 SS sheathing completely sealed to 0.4 bar
• With thermowell and dip pipe.
• Internal : Buff polished to 240 Grit.
• External: Buff polished to 180 Grit.
• UNDER FABRICATION, WILL BE FACTORY COMPLETE WEEK OF DEC 15 2025! Support Type: Lugs.

standard 6' diameter bucket with 18" diameter manway and 8" diameter outlet with 9 to 45 rpm on bucket with Hastelloy vacuum arm with stuffing box. With bull and pinion Reconditioned gear box, driven by 3HP XP class 1, div 2 , 3 phase, 60HZ, 230, 460 Volt motor with electric 10 ft-lbs. brake.

• mobile laboratory filter/dryer with tilting mechanism,
• design pressure internal 1 bar + full vacuum @ -20/150 degrees C, jacket: 6 bar + full vacuum @ -20/150 degrees C,
• all wetted parts are Hastelloy C22,
• 50 liter slurry capacity,
• 20 liter cake capacity,
• 350mm diameter x 680mm straight side,
• 6-30rpm shaft speed,
• agitator driven by 1.5kW, 3/50/230/400 volt, 1420 rpm CE ATEX EExd IIB T4 IP55 motor,
• hydraulic driven agitator raise/lower mechanism with powerpack,
• alloy 22 bellows on shaft,
• flat bottom filter plate with mesh filter and can be rotated for cleaning,
• manual vessel tilt mechanism,
• strip sight glass on side for measuring cake depth,
• approximately 100mm side discharge which is fully contained in a glovebox.
• all mounted on stainless steel frame with wheels for full mobility,
• design code ASME VIII DIV 1 (1998) + A '00'
• Can be used with 248331 APOVAC system for vacuum at an additional cost.

Double Drum Dryer

With vacuum housing and vacuum skid

Chrome plated carbon steel drums with 304 stainless steel, jacketed vacuum housing

Sanitary and polished construction suitable for food and pharmaceuticals but can be used for any batch processes, or converted to a continuous process.

Drum rolls have a 16 micro-inch finish, all internals have a 32 micro-inch finish

External finish is 2B or bead blast

Vacuum housing is rated to operate at full vacuum

Drums are rated for 160psi/FV @ 375 degrees F (NB# 9918 and NB# 9919)

Designed for use in class 1 division 2 atmospheres

1287 lbs./hr. of H2O and Ethanol

utilizing a 3.8 to 4.6 lbs./hr./ft2 evaporation rate

Spring loaded screw type manual adjustment assemblies with digital drum gap display

Pneumatic cylinder adjustable 304 stainless steel knife bars with clamp and acme thumb fasteners and pneumatically operated stainless steel end scrapers

8 zone steam jackets rated for 160 psi at 375 degrees F

(4) 6” tri-clamp top chamber inlets, (4) 4” tri-clamp product feed inlets, (2) 14” 150lb ANSI flange vapor outlets

(14) 1/2” NPT hot water jacket nozzles, (2) 1.5” NPT hot water jacket nozzles, (6) 4” tri-clamp internal drains, (10) 4” tri-clamp light ports

The Vacuum system is rated for 140 CFM, and is 304 SS contact, capable of handling 1,340 lbs./Hr. of vapor rate

Manufactured by Wintek Corp

Model # C380R50-WSS-=140/2-1FRss, serial # 140321

The skid mount system contains the following equipment: One-(1) 380 square foot, 304 SS contact, shell and tube pre condenser

TEMA C AEL, requires 180 GPM of cooling water at 50 degrees F

One-(1) Non code 304 SS 50-gallon receiver, with condensate pump

One-(1) Vacuum pump, SS wetted side, manufactured by Dekker, rated for 140 CFM, direct driven by a WEG 10 HP motor at 1750 rpm

One -(1) separator tank, non-code 304 SS, approximately 10 gallons

One- (1) Sealant heat exchanger, non-code, plate and frame, SS process side, requires 10 GPM cooling water at 50 degrees F

All equipment mounted in a CS frame work with ss interconnecting piping

The control system is a free standing Panel View Plus 1000 in a nitrogen purged enclosure good for Class 1,Division 2, Group D

It is located local to the machine, but will also send a signal to a remote control room

Located outside the classified area are the motor VFD, and electrical controls

• Variable speed motor based on load.

UNUSED

Internal finish 240 grit buff polished-Bright polished, external buff polish to a matte finish. ASME NB rated, and "U" stamped.

welded dish heads (2:1) 12 mm thick

Coil: 114 mm OD x 4 mm thick,

Limpet covers bottom dish and 2615 mm of straight side (pitch 150mm). Coil heating surface area.

With Insulation rings and upper drip ring. Two top lifting lugs and one tailing lug.

20" Manhole with Cover and davit arm assist, one 6" sight glass, Support Type: Lugs.

Vapors handled: NH3, N2, toluene vapor, 100 #/hr HCL, 180 #/hr SOC12 vapor

jacketed Loedige ploughshare mixer with choppers
machine #7644
behalter #1952
jacket pressure 0.5 bar @ 110 deg C (180ltr)
chamber 1110mm diameter x 2960mm straight side, internal rotor with (10) plow blades and (2) end blades, blades are removable
via a reduction gearbox, packed gland on shaft, c/steel jacket on straight side only. (4) 321 s/steel choppers each belt driven by a 2-speed motor 7.5 kw 3/50/230/460/380/420 volt, 2950 rpm or 8.5 kw, 3/60/440/480 volt, 3510 rpm
(8) spray nozzles, openings top: 3-350mm, jacket: 6-50mm, straight side: 2-540mm wide x 400mm high inspection doors, 2-50mm (for probes), bottom: 3-300mm long x 200mm wide each with a pneumatic operated valve, 8-25mm (spray nozzles,

IP55 motor, water cooled, with integrated air dryer, mounted in an acoustic cabinet,

w/(3) feed screws.
Discharge hopper w/out valve
Stirrup type hammers.
Rotor belt driven by 30 HP, 3/60/230/460 volt, 1770 rpm TEFC motor. Feeder belt driven by 1/2 HP, 3/60/220/440 volt, 1140 rpm TEFC motor.

150 Gallon,,
vertical dispersion mixing machine with jacketed vessel.
Dispersall Mixer Type VP,
vessel rated for Full vacuum at 4 psi. Vessel size is 33.5" diameter x 41" deep, with removable top and welded bottom. Mounted on a stand. Two top mounted planetary mixers with Teflon scrapers. One under driven high shear mixer.
With Waukesha model 25 SS positive displacement pump, with mechanical variable speed drive. Pump serial # D0261137SS. Overhead gantry for top removal.

Twin Shaft Nara paddle
Shell WO Number DS-220,
Jacket Serial Number D-258, National Board Number 1102.
Heat Transfer area: Jacket 107 Sq Ft, Agitator 293 Sq Ft, total 400 Square Foot.
twin shaft with discontinous wedge shaped staggard paddles.
Both jacket and agitator rated for 165 psi at 425 degrees F. Indirect heat, by saturated steam heat; rotary joints on shafts with quick disconnects and zero speed switch on end of shaft. Shaft seals are Meco Systems self-aligning externally adjstable, fully split elastomer seal, with purge port. With a 316LSS dome type covered trough rated for 5 psi pressure. With a chain and sprocket drive, SEW Sanasaio Parallel shaft speed reducer and a 75 HP Reliance motor. Motor data, ID # OIMAN 79345 G001 BC Frame 365 T, rated for 1780 rpm, Volts 230/460 amps 172/86 3 ph, Hz 60. Shaft speed approximately 12 RPM.
Openings include: 15" x 36" feed opening, (1) 12" diamter vapor opening, (3) 18" x 24" explosion vent openings, (1) 6" Sweep Gas Inlet, (1) 20" x 20" Access hatch with bolted cover, (2) 6" view ports; trough has (1) 12" x 58" flanged discharg opening, (2) externally adjustable weir gates.

Single Use Fermenter

• 5:1 Turndown Ratio, 3:1 Height to Diameter ratio.
• Jacket area 7.77 Sq. Ft., Jacket volume 10.85 liters
• 4 Tank Baffles, Internal impeller 2 HP drive motor with 5:1 Gear reduction
• Max rotation speed 375 RPMs. Internal Finish: Buff Polish. External Finish: Buff Polish .

Downflow dust collector
500 to 3,150 CFM air flow
With 4 filter cartriges
Housing has a hopper bottom with a manual valve designed to discharge into a pail
3600 rpm blower
3/60/230/460 motor
Includes Torit digital controls

Electric hot oil heater
Heat output: 1,229,194 BTU/hr
Complete system with (2) vertical 180 KW electric heaters, 3/60/480 volt, Serial Number J600-1 & 2
circulating pumps

• Body Only, base body
• Four Bosses for agitator.
• Glass type PureGlass (Pharma Grade)
• Exterior Paint :UGE blue Acrylic Polyurethane
• legs with flat plate feet, with 18” clearance bottom nozzle to floor.

• Vapors handled: NH3, N2, toluene vapor, 100 #/hr HCL, 180 #/hr SOC12 vapor

basket only
1/4 " drainage holes
Eight 7/8" bolt hole pattern